Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
PLASTIC intake froze causing a cracked in the hose thread input connection
Removed the back washer panel,unscrew the control/dial panel section from main washer body, remove part. Insert new part and put everything back in place. Really quite simple. DONE.
I had to take the motor and transmission out. They are one piece. Removed the clutch, take off trans. cover, remove a snap ring, take the striped gear off, and put the new one on. Then put put everything back on the way it came off.
Fast simple and supper easy! Please do not waist your time or money on repairmen that rip you off. You are garunteed all the way or your money back from Parts Select. Go to your model number than read a few stories of others to better pin point your problem then order part and your item will ship fast I had my part on the 2nd day of the order. Do not be fooled you can do it easily! I have order twice and both items went smoothly and took less then 10 minutes to put in. Thanks Parts Select for making it possible for the little guys and supporting them and not the big rip off scammers. I will be back when needed. May you continue in your good deed! C.S.
Although the motor was running, washer wouldn't agitate or spin.
After disconnecting the electrical supply, first remove the two screws at either end of the control panel and fold it back away from the washer top. Then, unplug the electrical lid switch connection. Now, remove the two clips at either end on top to disconnect the housing from the washer back and chassis. The motor is sandwiched between the water pump in the front and transmission at the rear. The Direct Drive Coupling connects the rear motor shaft to the transmisson. After you have taken the outter portion of the washer off, remove the two snap clips that hold the water pump in place and slide the pump off the front shaft. Best to also disconnect the upper hose connection so the pump can be moved out of the way. Caution though, remaining water in tub will drain out. Now remove the two screws that hold the clips in place which secure the motor to the transmission. Careful, as the old Direct Drive Coupling is probably destroyed, the clips are the only thing holding the motor in place and the motor needs to be supported so it won't drop to floor when the clips are removed. Be careful not to lose the four rubber grommets which sit between the motor and transmission bracket. After motor is on floor remove the old plastic slip-on direct drive coupling discs from both the motor and transmission shafts. The new replacement discs have steel centers which do not slide onto the shafts as easily as the old plastic ones did. I had to tap the center steel portion onto the shafts using a hammer and a deep wall socket the same width as the steel portion of the disc. Be careful! I'm sure that tapping the plastic portion of the disc to properly seat it on the shaft will break it away from the steel portion. In my case, It took me several attempts to completely seat the new discs. I had to do quite a bit of tapping to get the discs seated far enough onto the shafts so that the motor slipped easily against the transmission bracket grommets and the retainer clips snapped back into place easily. Reassembly is simply reversing the steps you took when taking the unit apart. Before putting the outter housing back in place, I checked to make sure everything was running smoothly by jumping out the electrical snap-in connection for the lid switch and running the machine in the spin cycle. Remember, if you don't jump out the lid switch and just try to test the unit in the aggitate cycle, the machine has to first fill with water.
Removed the softerner dispenser and the inner cap and seal. Removed the mounting bolt. Pulled on Auger and entire agitator came out. I needed to separate the parts. It said to stand on the bottom and pull on the top. I am an "older" woman and after wrestling with it for an hour without success I waited for my nephew to come by to separate the two pieces. When he did, it popped apart and all the parts went flying. Poor guy thought he had broken it. After conviencing him that that was what I wanted it to do, he left. Dirrections weren't very clear as to what went on first and I didn't have the convience of seeing it before it flew apart. Finally put it together and replaced the bolt. To no avail, something was wrong. My sister was making the same repair at her house across the street so we double teamed it. She came over and told me that I needed to put the Bottom agitator in the machine, then the spacer thrust, then the auger, then the assembled cam and cam dogs, then the bolt. All went well and was working.......so we thought. Started a washer load and the washer started leaking water. Don't know why, still don't know why. All I did was remove everything, put it back the very same way, and it hasn't leaked since. Go figure!
washer wouldn't start up after filling & closing lid
First I loosened the 2 screws on the outside of the top control assembly with a philips screwdriver. Then I took out the 2 other screws toward the top on the back with a socketwrench.Next I removed the top so I could access the switch. After that I removed the broken switch and unhooked from wire hareness. I then hooked up the new switch and snapped into place. Last I put the top back on and screwed into place.
Top Half of Agitator would not function without appying sideways pressure
Heard about the website... 1 minute to find it, 10 minutes to order new cogs... 3 day wait for new parts... Rec'd Fedex, 15 minutes total to pull the agitator cover (bleach dispenser) then the bung cover with o-ring (just lift out) expose bolt, unskrew and remove top portion of agitator or entire agitator if it's easier. Seperate, remove black cog holder (slides up the spindle) and replace cogs one at a time just like the old ones. Reassemble in reverse and you are back in business. Saved the $75 deductible on my home appliance warrenty. You guys are the best... cheers...
Agitator was barely agitating. Making a clicking noise.
Removed agitator cap. Removed bolt inside with socket wrench. Located plastic cogs Pulled out old cogs and slid in new cogs and put back together and works great. Easy to take apart and put back together. Very cheap repair. Cogs less that $4.00 plus shipping. Shipped next working day.
Actually this is kinda funny. I ordered the part and it arrived when I was out of town on business. My 20 year old daughter tipped the washer up on its end, and replaced the pump herself in less than 30 minutes. Her only complaint was that no one told her to block the washer up as it almost fell on her.
Remove the nut from the top of the motor shift inside of wsher. then remove the wire harness plug. Take out three bolts side the shaft and motor out. Replace clutch and install in reverse order.
washing machine would not agitate clothes during cycles
first I removed the fabric softner and water seal from center of agitator, then I removed the bolt holding it on. All I had to do then is install new agitator with old bolt place water seal and fabric softner container back on and start washing clothes again. Very simple.
First, I'm glad I found PartSelect. The previous posts for this repair told me exactly how to replace the pump: I unplugged the washer and moved it out away from the wall (did not need to disconnect water hoses). Then I tilted the washer back and propped it up so I could get underneath. Using pliers, slid hose clamps back and disconnected hoses from pump. Using a screwdriver, popped off two clips, top and bottom, that hold the pump in place. Pump then slides right off the shaft. Installation is the reverse. Make sure you align the shaft with the pump. Delivery of my part was FAST - ordered it and got it the next day!
removed two screws and atc knob. swung control panel out. unplugged atc switch. pushed little tab down and turned the switch. it popped out and I put the new one in. plugged the cable back in. repositioned the control panel. replaced the atc knob and turned it to rinse. Voila!!! it works.
leaking drain pump. Obviously a common problem with this washer
Just turned the washer on its side, popped out the two retainer clips with pliers and screwdriver, pulled the pump out by hand, put the new one in and replaced one rusty clip with the new one from parts select, and used the other old one. I ordered the parts on Monday, and they came tuesday, even with the standard shipping. Also the website parts diagram and whole website design is good.
I removed three bolts from the transmission and two clips that hold the motor to the drive gear. I replaced the brake cam that had cracked and the lining. Now it works great ! Ordered part on Friday before two and it came Saturday at four.