Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Washer would not start.
easy process: troubleshoot problem on website-- order part--get part--watch "how to replace"video on you tube-- get it done with only a screwdriver--go out for movie and dinner with $$ saved.
The washing would stop in mid cycle and the door would be locked.
An initial issue was getting the door to unlock. I tired several things but finally was able to pull the door as if to open it and put something between the door handle and the front of the washer while I ran a washer cycle. There is a way to take the washer top off and reach down inside the unit and pull down on a release, but I did not try that.
The washer has a rubber boot between the washer frame and the wash tub. There is a metal wire ring that secures the outer edge of the boot to the washer frame. Peel back the outer edge of the boot at the bottom to reveal a metal ring that has its ends connected by a small spring. Use a flat tip screw drive to pry this ring off. Peel back the boot from the washer frame.
Next use a Phillips screw drive to remove the two screws that protrude through the wash frame on the right side of the door.
Reach between the washer tub and the frame and the tub and pull the switch through the opening and the washer tub. You will have to wiggle the switch around to remove it. There are three sets of wires attached to the switch by plugs.
The switch is covered with a plastic protective cover. Remove this. You will have to use a screw driver to release various catches to do this.
Remove the three set of wires. There are catches that secure the wire plugs in place. pry them back with a small screw drive.
Attach the new switch to the sets of wires.
Attach the protective cover to the switch. The wires feed through a small slot toward the bottom of the switch.
Slide the switch through the opening where you removed it. and re-attach it using the two screws.
Put the rubber boot in the channel in the washer frame. Replace the metal ring. This was the most challenging part of the repair for me. I had to play around with this to get it into position. You have to work it around the gasket and stretch out the spring.
By the way, The service was great and exceeded by expectations.
I am super excited that partselect.com asked me to do this review.
1-Order part on website, validate that everything is correct. It was. PS11741552 2-Part received is going to be a small box of screws instead of your vastly overpriced plastic door latch. This will happen your first time ordering, it is normal. 3-Item refunded through customer service and a new item sent out. 4-At this point you will need to do laundry, my recommendation here is to put you back against the door, maybe read a book and have a drink for the half hour it takes for a cycle. Nobody with a washer wants to hang out with the unwashed masses at the laundromat. 5-Receive another box of screws. It this point you will now believe that the screws are a metaphor for how partselect feels about customer service. 6-Contact customer service again, get another refund. At this point partselect will just give up and tell you to order the parts from the manufacturer. Once again by the picture on the site and the confirmation, you have order the correct part. 7-Total time here is over a week to 2 because the parts move slowly. 8-Order part on literally any other site. 9-When you get it unscrew the 2 screws from the broken part. Replace with the new part and screw the 2 screws back on. Fixed!!
Unplug machine,remove three screws that hold on top cover. Unplug latch switch assembly,then open front door of washing machine, remove three screws which hold latch switch. Install in reverse order.
I had to pull the washer out from the wall. SInce it is in front of the door going out into the garage made it dificult getting tools. I had to lay on my side doubled up in order toget to the hose. I used a bit extention so that I could get the clamp loose. Cut the time in half by using a drill with a phillips head screw bit. The only real hard part was getting the new one up tight on the drain. Used a heavy duty screw driver to push it up so the clamp would bite.
Washer flashed error code DL (door lock) and wouldn't start.
We followed another very helpful repair story. Unplug machine. Unscrew top back screws, remove top of washer. Reach inside from the top in the front of the machine. Remove screws holding latch in place, unplug the three plugs attached to latch. Replace with new door latch, screw it in place, replug the three plugs, put top of machine back on, replace screws on back and your'e done! Works great! Job made easy thanks to others helpfulness!
I had noticed the latch on door was split so I ordered the latch, but before I could put it on, the latch on the front of washer was locked. I then looked at the messages from others on this site for help. My daughter and I unscrewed the 2 screws on the top back, removed top, pulled the control panel up, unscrewed the front, unscrewed the 3 screws for latch, pulled old one out. I located the part, ordered it and got it in 2 days! Put new latch in and screwed everything back the way it was and in 15 minutes, the washer is running! (I am a woman too!)
The washer tech manual stated to: 1) remove the top, 2) control console, 3) front below the door (front load washer), 4) remove the retaining wire, 5) pull back the rubber bellows, 6) remove the three screws and remove the door latch/lock assembly. I discovered that steps 1 through 3 are not required to replace the assembly. Installation is the reverse of steps 4 through 6. That was easy. The difficult part was figuring out how to reset the pressure switch so the drain pump would not start every time you reconnected to the power supply (pressure switch thinks the washer still contains water). With the power disconnected, I disconnected the pressure switch from the central control unit. Then I reconnected the power supply and pressure switch. That reset the pressure switch solved the problem with the drain pump. Washer works fine now.
It is very easy. Unplug from the wall. Take out the two screws from the back that holds on the top panel. Unscrew the three screws inside the door by the latch. Reach inside the washer from the top and unplug the three plugs on the latch part. Then plug in the new part , put the three screws back in. Then put the top panel on. Plug in and magic. It works!
This took ten minutes .... super easy .... DO IT YOURSELF!!!! About 75.00 with shipping ... can only imagine this woulkd have been 250 to 300 to have somebody com e onsite.
The Glass on the door cracked into a bunch of pieces.
I went to Maytag.com and typed in my model number and it came up with different parts I found the glass part I needed and ordered it. I received it in like 3 days. I had a phyllips screw driver and it the removal of the base around the glass replace the glass and screwed it right back on and started washing clothes. No leaks at all. I am a woman and proved woman can do the same things a man can do but quicker.LOL
Machine won't run. Door won't open. Makes buzzing sound
Removed top cover. Manually opened door through top cover opening. Removed 3 screws at front holding assembly. Removed 3 harnesses attached to assembly. Replaced with new assembly and screwed back in. Replaced harnesses. Certainly an easy DIY job.
