WF219ANB Samsung Washer - Instructions

1. remove the three screws from the top backside of the top panel
2. push the top panel to the rear 1/8 to 1/4 inch
3. lift/rotate top panel from rear to front, set aside.
4. remove the three wire connectors from latch.
5. use #15 Torx to remove the three screws from the latch.
6. remove and replace part using to ... Read more p opening.
7. reverse order to finish.

I bought a new door lock for 132 dollars (item number PS2037196).

Ultimately you have to get to the inside of the machine where the door lock is located in order to see if you will need this door lock that I bought.

DISCONNECT POWER FROM MACHINE.

First take off the top by taking off the 2 screws on the bac ... Read more k of the machine.

Second take off the control panel, I believe there are about 5 or 6 screws for that.
(there's also a screw when you open up the detergent compartment on the bottom left- also, a lever must be pushed in order for the compartment to come off- it MUST be taken off).

Third unscrew the top of the front white plate.. there should be a 5 or 6 screws for that.
You don't need to take off the entire front plate.

Finally unscrew 3 screws that hold the door lock in place .. make sure your hands is in the machine- the back of door lock to catch the lock when you're on the last screw.

Gently take out the door lock from the side with the cables attached by holding the white metal door open (it bends).

Try to pull on the bottom of the door lock (its a manual release). If it doesn't release you need to buy a new door lock like I did... if it does release then you don't need a door lock and just reassemble.
(Note: You can also try plugging in the machine and THEN pulling down on the manual release. When I tried this the door lock just vibrated and nothing happened so I bought a new door lock.)

If you have the new door lock continue here:

Take out all 3 cables on the old door lock by pressing on the corresponding clips.

Attach the new door lock with the correct cables. Assemble machine back together.

Thats it.

replaced door latch but door would not close had to remove latch assembly and reset the latch in the latch assembly. To reset latch in latch assembly you remove the black plastic only on latch assembly then press the spring down with thumb move the black plastic catch back to the latch position. when you remove the black plastic there is ... Read more four metal switchs and one spring that you have to pay attention too so remove very carefully.

Had to take the entire front of the washer off to replace the door latch.

Peel rubber gasket from drum; remove 3 screws using phillip head screwdriver; disconnect wiring e plugs; remove door lock. Install in reverse order.

Never thought that the glass would break like it did. Removed the whole door assembly and took out the screws that hold the plastic retaining ring for the glass door. Replaced glass and reassembled the door. Very easy repair. Took about 15 min.

I took the two screws off the back that holds the top down, lifted it , then pulled it back to remove. After this was removed, there were two more screws holding down the assy-s housing and drawer. First remove drawer where you add the soap and softners. Then I pulled that back and the assy-s housing drawer just snaps onto the housing. I ... Read more pulled the drawer off, then I took the four hoses that are connected to the back and put on the new one in their respected spot. I snapped it back on and reassembled. You don't need a maytag repair man to do this job.

Pull washer away from wall and find two screws in back next to top edge. Undo and pull top of machine off (lip on fron edge under face cover). reach down and unplug three plugs on door latch small one on top, biggest on bottom. Unscrew the three screw holding the latch on the front of the machine, take out the old and put in the new. ... Read more Note, I pluged in the plugs before screwing the new one in place, and that might be easier. Put the top back on.
I couldn't find any way to adjust the door, so you still have to lift it up when closing.

The dog ate the door latch so I ordered a new one. All I had to do was unscrew the old one, remove, and screw in the new one. Super easy. Took longer to find the screwdriver than it did to make the repair.

The best way to do it is not the way I started.
The best way is to 1st remove the bellow's front clamp with a small screwdriver at the spring. 2. unplug the 3 sets of wires attached to the lock. 3. remove the 3 screws on the front that hold the lock. 4. remove the plastic ribbon harness that attaches to the lock. 5. remove the old l ... Read more ock. 6. install the lock back carefully moving aside the cables. 7. install the 3 screws. 8. attach the ribbon harness. 9. attach the cables. 10. replace the bellow. 10. replace the clamp (here you may need someone's help to keep the rubber in place.) 11. the last part to fall in place is where the spring is. 12. If you can't do all by tact then you may want to remove the 3 screws from the top cover to be able to c where all fits.

Watched the video, procedure was simple and as depicted on the video. Started by using a wet shop Vac to the discharge hose and sucked as much dirty wash water out as possible. Removed the pump,and found the motor did not turn freely. Removed the motor (3 screws) and replaced the motor with new part. Reassembled the washer, everything wor ... Read more ked as it should. After about 3-4 loads of laundry, the "Not Draining" code / problem returned. Again, sucked out the water with the Shop Vac. Checked the Filter /Cleanout and found it completely packed with MUD. Cleaned that out, and again disassembled the washer. The pump was removed and the remaining muddy gunk was cleaned from the impeller. The 3 drain lines that attached to the pump were inspected for blockage/obstruction and flushed of any muddy residue. Reassembly was quick and easy, and the washer has worked well since. I have no idea how the dirt got into the system with enough dirt to gunk up the system. Recommend keeping more frequent inspections of the cleanout trap.

(1) Remove all screws keeping them organized as a set,(some are larger than others,for the glass frame only. After all screws are removed remove frame from the door.(2) Remove old glass and replace with the new one and put it all ack together.

Took off top. Removed front control panel.Removed top screws on front door panel,then I had access to door lock for removal.Had to replace door latch also as this was broken while trying to close door before we noticed the door lock was not working.

removed all the panels to change the door latch switch
plug in three plugs ...works great
Thank you

Removed the washer tub gasket and then removed the door part that I order . It was real easy to replace it and the tub gasket . Took about 8 min to complete everything .