Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Friction sleeve had torn, resulting in dishwasher door 'falling' when opening.
I unscrewed the dishwasher from the counter (two screws under the countertop), and pulled it out about a foot so I could access the friction sleeve. I used a needle nosed pliers to slip a spring latch off the door. Then I slipped the new friction sleeve on and reattached the spring. Tested the door. Success! Super easy. About 5 minutes of work.
Looked under machine, saw wire going to heater was burned off.Seal on heater failed, water leaked onto terminal, shorted and burned, ruined plastic terminal nut.Replaced heater and wire terminal, and nut, took minutes, works great.
easy as long as you have the right tool to take the panel off, maybe they could include one for people who don't have a good selection of tools. Thankfully we did.
I opened yutube and noted the tips on how to fix specific problems with my dishwasher. That "steve" guy was very helpful. I tested the old bi-metal fuse with no flow and ordered a new replacement through partselect. The part arrived in one day and was fitted quickly. I used the teat meter to confirm that the fuse was ok before I installed it. The only problem that I had was identifying the part and number from a diagram which I did not have.
I removed the lower front panel of the dishwasher to expose wheels and opened door and removed two screws holding washer to cabinet. After raising leveling feet pulled washer out to expose bnotton ow dishwasher. Removed the electrical wires form the heating element and removed screw caps holding the heaqting element in place. Removed the old element and inserted the new, then reversed process to get it back together. It was very easy to do following the instructions I received when I ordered the part.
I did not relize that the drain hose was in two parts. Naturally I ordered the wrong half. So after I relized my mistake, I re-ordered the correct part. Once the correct part was received the repair was easy and went well.
I researched the internet about this symptom on the Kenmore Elite Dishwasher and I found lots of people with the same problem. Everyone fixed it by replacing the Bi-Metal Fuse. I removed the old fuse and tested continuity and it was indeed bad. Once the new fuse arrived I tested continuity and it of course worked as expected, so that was a nice wipe of the brow. The new Bi-Metal Fuse came with a nice instruction manual. I also used a video from YouTube to help with the repair as well, but the included instructions were enough. The only thing that was not clear was the best way to attach the new wire since it was quite a bit longer than what was orginially there. So I ended up just folding it up and putting everything back together and it worked just fine. This repair was very easy as long as you are OK with cutting and stripping wires in a somewhat confined space and not being too worried that you might mess it up for good... :)
First I identified the problem by checking the plug ends of the heater coil with an ohm meter. I quickly odered the part and when it arrived a few days later, I simply pulled off the electrical connectors, unscrewed the two bolts, removed the old/broken coil, put in the new coil and tightened down the nuts snuggly. Nothing to it. I then had to reset the error code and it is working like new.
The Spinner at the top of the dishwasher came off and would not stay on.
First of all I appreciate the instructions provided by this site when I selected the part I needed! The installation was so easy. I popped the end caps off of the top rack guides and removed the top rack. I reach in and popped the clips holding the top sprayer bar and gently pulled down on the sprayer bar enough to place the spinner button in the top of the sprayer bar. Then pressed the spinner on the bottom of the sprayer bar into the button I place in the top of the sprayer bar and reattached the sprayer bar to the clips. Put the top rack back on the guides and replaced the guide caps and it was finished. Easy fix thanks to this site great instructions!
