Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
I didn't know if I could get a replacement part, but I googled "replacement parts" (or some such), and since this website looked easy to navigate, chose it. (Actually, I did my ordering via telephone). The sales rep. helped me clarify which part I needed, I ordered it, and received the part the very
I simply snapped the two end pieces into place, attaching the guard rail. It was like putting the pieces of a very easy puzzle together‚ especially for someone like myself who is mechanically challenged.
I ordered 2 end caps just to keep one as spare. Turned out I had ordered a size larger than the one already on the refrigerator. So I replaced both ends and it worked fine - with increased shelf space. Now I can even fit a gallon container with ease!!! Took about 20 seconds. I just wish there was an easier way to measure parts before ordering. Otherwise, the entire process from order to finish took about 3 days.
I watched the video online, followed the instructions and within minutes had the part installed. The frig light was working once again! I will say the original switch was very snug and I had to do some very minor scraping of the plastic to get the new part to slide in.
Turned off the breaker to the fridge because I couldn't reach the power plug to unplug it . Use small flat head screwdriver to pop out the piece, disconnected the rubber prong connectors, inserted the new piece into the rubber prongs snapped it back into place. Flipped the breaker back on and prayed it worked. It did and I saved myself $120 service call.
Fan would not turn when the refrigerator came on all the time. Would physically have to turn the fan blades.
Did not do the repair because the unit arrived damaged. The packaging was in good condition. The plastic around the plug in shattered, and some of the plastic was inside the motor. Very good, and fast on adjusting the order.
The refrigerator would not stop running, resulting in frozen food in the refrigerator compartment.
After reading the trouble shooting section of the owners manual, I determined, without much difficulty, that the temp control was defective. I checked some local outlets and found the prices running from $36.00 and up. The same part from this site was around $20.00. Guess where I bought mine! It arrived in a timely fashion, and I installed it with no problem, in about 10 - 15 minutes. This was a very easy job, just remove and replace three wires snap the unit into place, and screw the cover on. Tip: I always use you tube or another source to get some instruction, just in case I'm not as smart as I think I am!
got on part select web site and found other customers that had same problem and on their site they had comments from them to fix problem. I then took off back panel on frig where compressor is by removing 6 screws and found the relay attached to the compressor then pressing down on holding spring removed 2 wire alligator clips and it was bad ordered one from part select put the new one on an frig was fixed. entire fix took about 30 minutes from isolating problem to fixing it. thank you part select
0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot. 1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back. 2. Pop off the hemispherical glass cap. 3. Unscrew the old light bulb, and screw the new light bulb in its place. 4. Put the cap back. 5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
Fridge never cuts off.freeze everything inside of fridge.
To remove the temp sensor.2 Phillip head screws not remove the cover inside fridge .the temp control knob cover.removed that and unplugged switch.installed new switch.reinstalled cover.
The plastic parts that hold the brackett to the shelf were broken.
The part just snapped into the shelf bar. Extremely easy to fix. Since you show the part in a grid I was able to tell, by holding my old piece up to the screen, that the new part would be the correct size. We have rentals and are always needing parts for appliances. Impossible to find locally. Also the part came so quickly it was almost as good as buying it here in town. Thanks. Donna Bingham
