Models > SHP53T55UC > Instructions

SHP53T55UC Bosch Dishwasher - Instructions

All Instructions for the SHP53T55UC
46 - 51 of 51
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Handle on Bosch dishwasher had cracked
1) Remove the three torx screws securing the handle.

2) Open door. Placing some cushions under the door makes the operation easier.

3) Remove the 12 torx screws securing the door skin. Note the screws are of two sizes. The lower 6 are shorter and fatter than the upper 6, that also secure the control panel.

4) It’s useful to have a 2nd person or a counterweight to secure the door once the skin is removed.

5) Remove the old handle by snapping the securing tabs.

6) New handle is press to fit.

7) Return skin to door and re-insert screws to secure.

8) Re-insert the three handle screws.

Notes

1) A three red wire cable plug was floating in the breeze when i removed the skin. I assumed it had pulled loose during removal of the skin so inserted back into the control panel but the washer would not power up with it inserted. On removal it worked fine. Not sure it it serves a model specific function.

2) It may be possible to use a car trim pry tool to remove the handle but I was concerned the stainless might be distorted.
Parts Used:
Door Handle - Silver
  • spencer from gilbertsville, PA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
My flow tube had a hole in it
Initially, I received an E15 error. I evaluated for leaks but couldn't find anything except for water in the bottom of the dishwasher after about 30 minutes of the initial cycle. After discovering the hole in the flow tub, I order the part. It came a few days later & replace the part within a 15 minutes of receiving it. I didn't think it would resolve the issue but it did. Thank you!
Parts Used:
TUBE
  • Rick from LANDENBERG, PA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Four wheels on the lower dishwasher rack came off and got lost.
I bought replacement wheels.
I put them on the post, and they snapped onto the vertical post very easily. Job done.
Parts Used:
Dishrack Roller - Grey
  • james from PARSIPPANY, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
dishwasher not emptying tub, dirty dishes when the dishwasher said the cycle was done
easy repair, but the check valve wasn't the problem, it was the float switch that isn't on the tech sheet in the dishwasher or mentioned as a possible culprit anywhere I could find on the internet
Parts Used:
VALVE-NON RETURN
  • daniel from AUBURN, IN
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
One Dishwasher bottom rack wheel broke
Popped the new one right on!
Parts Used:
Dishrack Roller - Grey
  • Toni from GREENSBORO, NC
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Top arm water connection to rear wall - all seals eroded and leaking
Removed the middle basket and turned it upside down. Unplugged the spray arm from the middle basket. Snapped the new spray arm into the middle basket.
Installed middle basket into slides.
It works great. Great site for parts - reasonable prices too
Parts Used:
SPRAY ARM
  • James from MOORPARK, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the SHP53T55UC
46 - 51 of 51