Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Plastic Lid Hinge was broken
Changing the hinge was not difficult, but here's a hint: the top of the washer raises up if you pry it with a big screwdriver- be sure to wrap the screwdriver in a cloth so as not to scratch the appliance. Doing it this way makes it easy to access the retaining screws. You can push the wash tub to one side and reach the screws from underneath, but they're a tight fit and doing it that way is difficult. Overall a pretty easy repair and I'm only moderately handy.
1. Remove 1 screw holding each of 2 Hinges - use T15 driver. 2. Push tub to one side to get access to each screw from underside. 3. remove & replace broken Hinge Pin from Lid with T15 driver. 4. Drive broken pin out of the Hinge with a punch & hammer. 5. Install new Hinge Pin to Lid. 6. Add a little Vaseline to Hinge Pin & slide Hinge Pin into Hinge. 7. Line up Hinges to holes & re-install both Hinges with Lid. Have somebody help hold the Lid in a slight angle will make re-installation easier.
Removed front panel from washer,removed belt, used 1/2 inch socket setand channel locks to remove hose and pump. Installed new pump, reinstalled hoses and belt, and placed front panel on machine.
i removed 3 screws from back of washer , took off 2 hose clamps , then i took 4 screws out of waterpump, removed belt . put new pump on very easy. thanks part was perfect, fixed problem
crack in tub hose causing washer water to spill on to floor
raised the top of the washer to get at the front panel screws. Removed the front panel. Removed the cracked hose and installed the new one. Reinstalled the front and top panels.
Removed front panel by releasing spring clips with putty knife and removed two screws with a ratchet and 5/16” socket. Removed rear access cover with a ratchet and 5/16” socket. Removed and replaced tub to pump hose. Loosened clamps on each end of hose with channel locks. Re installed rear access cover and front panel.
Turn water off at the inlet valve of hose you are replacing. Disconnect inlet hose the washer and let water drain out in a bucket. Then remove old hose. Replace new hose to inlet valve then washer . Use pliers to tighten both ends. Turn on water to check leaks at both ends of hose.
I used the putty knife to release the spring clips on the machine lid. They are about 3" in from the side of the machine. Then I lifted the top of the washer up holding the lid in place. I then used a screw driver (torx) to remove the hinge from the bottom of the washer top. The lid should come right off. Then I the removed the broken hinge pins from the back of the lid with a screwdriver and replaced with the new parts. There is a little tab that the pin fits in the lid to assure you have the pin installed correctly. Then I slid the hinge back on the pin and reversed the process reinstalling the hinges and closing the top of the machine over the spring clips and your done. Very easy repair that I completed in less than 15 minutes.
There is a small back panel about 14" square made to open for access to the drain pump. 3 screws for the back panel and 3 screws for the pump - Oh you do have to slip the belt off & back on, underneath the machine.
Washer was making a squeak during spin cycle & then just stopped spinning
I watched the video of the repair on this website and followed it. Was really easy & THANK GOD because this was my first repair. This has been a great machine and it looks like it will continue to be for a little while longer! Thanks for the video help and friendly navigation of your site!
The top load cover would come off in your hand and it was so loose that the lid cover salety switch would not work
First I got everything I needed, unplugged the washer. Using the puddy knife I freed the top of the washer by inserting the knife about four inches from each side on front. The machine is in a place where it can not be pulled out far, hence the two by fours. Remove the loose cover, reach in with the stubby and unscrew the screw on both sides. Take the broken cover pins off the cover and install the new ones, put the other hinges in the cover, put the hole cover in place and install the one screw perside, remove wood and close the hole top, your in business , no drinking
I first changed the belt which helped but it still sounded like it was going to take off through the roof.....I did the pulley and bearing kit in hopes that it would do some good....it went really smoothly with no issues however it did not solve the problem....so it is working and I am going to just ride it out until it quits....thanks