Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Bearings making noise.
If you are using the newer style seal be sure the taper part of the seal is toward the front of the machine. Installing it backward will ruin the seal and burn up the motor and or controller. The seal installation tool will fit on the side oppsite the taper. It will require a helper to hold the drum support while torquing the nut on the pulley. Better instruction would help too.
The washer was stating NF code in the panel. It was not refilling for the rinse cycle. I had to manually press the button.
Turn the washer to the back. Unscrew the upper right corner water inlet valve. Take it out then replace it with new valve. Then turn your washer on and it will work just like brand new !!!!
my husband took the old part off. order the new part thru your company...3 days later the part came in. then he reattached thee part to the hoses with the champs and we said alittle pray and i had my washer back
I researched the internet and found my answer on this site. There were others who shared their experiences which made the repair easy. There was a leak in the front gasket between the drum and outer frame. I printed out several answers that customers had posted. I opened the front door on the washer and found a tear in the bottom of the gasket near the drain hole. To use the washer until the parts arrived (which only took 2 days), I used a bike repair patch to seal the hole in the gasket. NOTE: Don't use the glue type as it may get on the clothing. I used a patch that you pull off the backing and apply. It worked great until I got the parts. Another party had posted how he got the cable and spring attached on the gasket. He used fishing line. I used masonary string I got from Home Depot. I made a loop on one end and attached it with the spring and pulled both around the gasket after I had positioned it on the back drum. I looped the string over the other end of the spring and pulled. As the spring stretched, I hooked the other end of the cable on the spring. It worked perfectly. Note: Don't worry about the string being underneath the cable, you merely pull it out slowly and the hard part is done. I then hooked the front of the gasket into the slots and finished the job. It took about 40 minutes alone. P.S. Parts select got my ordered filled and sent to my residence within two days. Great experience and I would not hesitate to order from them again.
Ordered the new part from Part Select had very prompt shipment (2 days) printed out someone elses review and followed their steps and it was even easier than they had written so if you get this part simply print the only other "steps" listed because their correct. The only addition i would say is you can use a "nut driver" for the screws as well as the hose clamp which makes it simpler, and definitely mark where you remove the connections so they go back in the same location. Also it may be advisable to remove the big "drum cover" to get easier access to the water hose since it's a little short and difficult to get back on the new valve through the inlet valve hole.It should take you about 15 min to do
Using a screw driver I removed the 4 screws that hold the front panel and door on allowing me to remove the front panel and door. I removed the spring clamp from the drain hose and removed the drain hose. I removed the 4 screws holding the detergent access door on the top and removed the door alllowing me to tilt the top up and back. Now both sides of the seal were exposed. The front side of the seal is easily pulled loose and the back side is held on with a cable and spring tensioner. The spring and cable slipped of freeing the seal. I installed the back side of the seal paying attention to the alignment "ticks" in the seal and washer. I installed the cable assembly and spring using pliers to pull the spring into place. The front edge was pushed into place. I installed the drain hose and spring clamp, lowered the top into place, installed the detergernt access door with the 4 screws, and installed the front panel and door using the 4 screws. The only trick wwas getting the back edge spring tensioner in place. It took 3 tries over ~ 10 minutes. All other items were very easy. I watched the first load wash to be sure the seal did not come off.
It was very easy to do. I took the back cover off. I dissconected two hoses. disconnected one wire. removed a small plastic bag (cover over wires). turned the pump 1/4 turn.and reversed this process with the new pump. It took me 15 minutes to remove and replace. Put the washer thru a cycle and it worked!
the boot seal holding the drum to the front panel leaked
I replaced the boot seal. I unscrewed and took off the front door and front panel; I unscrewed and removed the detergent compartment; unbolted and lifted up the top panel. I removed the old worn out gasket and replaced the anterior (door side) portion first, then the posterior portion. the door side pushes right in by hand but I used a putty spatula to firmly seat it evenly in place. For ease of closing the spring loaded wire on the posterior portion of the gasket, one person held one end of the wire and gasket in place and a 2nd held the other side in place and pulled the spring with pliers to connect and seal the gasket. replacing the boot seal requires 1 person, but having a 2nd person around to help with the spring was helpful. this was an easy project that takes about an hour.
I removed the 2 screws holding the door and then the balance of the screws holding the front section on. Removed the trim piece and then the screws holding the detergent tub and top of the washer. Once the boot was exposed I used two pair of pliers to hold either end of the retainer strap and pushed together to relieve the spring tension. Then disconnected the drain hose from the bottom of the boot and removed the boot. Re-assembly was just a reverse of the disassembly and much easier than I anticipated. Placing the boot around the fron of the tub was like putting a bycycle innertube on a rim. Once you get it completely on then you place the retainer strap around the boot and attach by hooking the spring to one end and pulling the spring toward the other. (better if two people do that part but can be done by one) The front of the boot slides into the slots fairly easy and then you simply re-connect the drain tube in the front of the boot and reassemble the cabinet.
I opened the door on the washer,and pushed on inner tub upward.it moved about 1 inch and the I knew tub bearings where shot .So I removed all components and repaced the outer tub with new bearing pack.. NOTE... Not an easy repair..but when i finished i had no probems with water leakage.ALL GOOD.
On the Maytag front load washer, we found the easiest way was to unscrew and lift the top of the washer up, then take off the door, and front panel. Removing the old seal (moldy) was easy, but to replace the new one you need to see what you are doing. (Reaching up blindly to slip the new seal around AND connect the spring, is near impossible.) It was not hard to do...IF you can see what you are doing. You need access to attach the drain tube, make sure the gasket is slid in place (with notches in line with openings) slip the cable around and attach the spring. Everything is easy IF you can see what you are doing (and a little muscle to pull the spring and connect it).
Opened a small door in the rear of the washer and loosen the two braces with a screw driver and pulled the old hose and replaced with the new hose replace the door and that was all.
The machine comes quickest appart with a cordless screwgun and a #2 Phillips.
To unhook the wire with spring it is easiest to use a needle nose plier and make a hook from a coat hanger or use a paint can opener.
Pay attention when yo line up the boot with the flange in the back, that the rectagular protrusions line up with the holes in the flange. You may have to stretch the boot a bit and push it all the way in with a dull tool.
Get someone to help you put the wire back on if you want to do it fast and easy. Otherwise hook it on the spring and get the pliers on the loop on the other side and pull it together, torquing the wire back so that it does not make the boot slip fo the flange.
I found water on the floor beneath the washer. Further inspection revealed the door boot was torn.
I removed the screws around the front door. Then removed the front face. I removed the bolts holding the top down at front top corners. I removed the detergent dispensor. Next I removed the spring and hold down cable. I then pulled out the old boot. I then, with the help of my son, pulled the new boot around the drum. Then attached the cable and spring. Next pushed the boot into the front retainer. I then put the dispenser in and the front back on. Good as new. It was not hard as long as you have someone to help with pushing the boot around.
