MSD2656GEW Maytag Refrigerator - Instructions

First I hired a repairman to fix it who charged $125 to defrost the cooling coils then said the defrost heater would need to be replaced for $125+labor. He had the wrong part and was going to charge me >3x the price it would have been from Partselect.com too. I figure I saved a minimum of $250 vs having him do the work then charge me yet again for the right part.

Should have just done this myself from the start and saved another $125. Information about the cause, how to test and what parts would be needed were all easy to find online once I actually searched.

Unplugged fridge.

Using diagrams from PartSelect.com and other information online anb defrosted coils with hair-dryer. (This requires removing two screws in back of freezer compartment using nut-driver to remove the panels covering coils... literally a two minute job to expose coils!)

Then found and tested defrost heater.
Defrost heater was fine. Per information online problem then had to be Adaptive Frost Control (ADA) circuit board.

In refrigerator compartment:
1) Removed top housing cover (covers lights, temp controls, etc.) This required removing a single screw (with nut-driver) attaching it to back and depressing two locking tabs near the back on either side. Slide it forward and down. The only tricky part of this repair is getting the locking tabs positioned correctly to get the plastic cover off. I did break the left one although it cover is still firmly in place in this case.)

2) Removed entire assembly from roof of fridge. involves loosening two large headed screws above lights and removing two hex-head screws with nut-driver above either side of temp controls. Next slide slightly to the right to disengage the two large-headed screws (or remove them completely... it seemed easier to just leave them in place.) Dropped front end of control assembly down.

3) Opened plastic box surrounding ADA and pried open locking tab holding it to wiring. Connected new board and set ADA assembly back in place.

4) Put everything back together.

Plugged fridge in and all was well. Exposed the coils again a few days later and they were not frosted up at all.

Total time to replace the ADA was about 20 minutes. Total time for everything including defrosting coils, testing, replacing parts, etc. was an hour max.

This was a very simpler repair to an annoying problem. First I removed the decorative cover on the top hinge pin of the door which was held on with one screw. I then removed the 3 screws of the top hinge pin with a socket, held the door in place with my hand and took off the top pin. Next, I simply lifted the refrigerator door off the bottom worn out hinge.
removed the old door hinge bracket and bottom lower hinge pin that had worn, placed the new bottom hinge pin in the bracket. Finally, on the bottom of the refrigerator I replaced the natural door closer held on by one screw. Lifted the door back onto the new bottom hinge pin, held the door in place and installed the top hinge pin, put the cover back on and the refrigerator is closing like it was new again.

First I removed the spill tray, and removed the two screws on the bottom of the dispenser. I was then able to remove the front of the dispenser, which revealed 3 more screws. After removing those screws, the entire assembly lifts out. I removed the old pad, put the replacement pad on, replaced all the screws and the tray, and was done! It took about 10 minutes, start to finish. I saved at least $75 on the repair by doing it myself, and the part only took 3 days to arrive. Best of all, the water and ice dispenser works like new! Thanks, PartSelect!

Chronically faulty electronic board in upper right rear of refrigerator compartment - in Maytag and Jenn-Air. Unplug unit. Remove freezer food to ice chest. Remove baskets and shelves, ice hopper and rear lower panel to expose evaporater fins. Defrost with hair dryer and allow all moisture to dry. Then in refrigerator, remove top shelf food. Carefully remove the upper assembly cover by working the plastic down and slide forward to unhook from rear slide attachments - one on each side. This is the hard part of repair.

Then remove screws from rear wall and just behind the lamps to release the whole control assembly. In the rear right corner is the bad board. Unplug and replace with new board. Reassemble the fridge and freezer. Replug unit.

first unplug the refrigerator (power) remove the dispenser platform (removable) remove two torx screws, slide the cover up unplug the wire from the cover by sliding the ribbon tape up from the circuit board, remove the three torx screws slide the plastic from the hose (water dispenser hose) unplug the electrical (2) remove the two torx screw from the magnetic relay reassemble the door about 15 minute if you know what you are doing

Confirmed the condenser fan was the problem when I noted it was not running when the compressor was on. Removed 3 mounting screws, unpluggede the fan. Removed and replaced the mounted flange(3 screws) and remounted. Plugged in fan and it started running.

Thanks for the diagrams and quick delivery. This is the second repair on appliances I have made with your parts and probably saved $300-400 in service calls.

Removed the ice bucket from the freezer. Removed the single screw on the left side with a nut driver, then lift and pull the tray toward you...there is a wiring harness in back of the tray that I had to unplug...easy, pinch the sides of the plastic connector and it disconnects..and the tray came out of the refrigerator...and the cussing started. Since the threaded yoke was stripped it could not be unscrewed from the motor shaft...I took my trusty Dremel Tool and cut the shaft off so the yoke could be separated from the motor shaft and the motor could be removed from the plastic housing. From here on it was a piece of cake...install the new motor and screw the new yoke onto the motor shaft... I think it has a left handed thread, like the old propane bottles used to have..slide the tray back in, reconnect the wiring harness (it only plugs in one way), make sure the tray is sitting on the 4 side supports, put the single screw on the left side and you are done....put the ice bucket back in and flip the bail down and you should be back on business....!!

First unplug AC power from the back of the refrigerator and I then removed entire fountain bracket assy that hold by 3 screws. Pull toward with some angle to able to access to a plug of wires and then disconnect it. Pull fountain assy downward. Set it on work place, remove all screws and transfer wires, switch, ice dispenser controller unit,solenoid, spring, flapper...and then install them to a new fountain bracket. Please note that this problem is 100% relating to mechanism. To test this work: Hold Fountain bracket assy vertically, press a flapper,position "open" and make sure return spring is working properly (enough pressure) . Now, install this unit back to my refrigerator. During installing screws, check flapper that can shut tightly enough and secure all screws, check a flapper again. I got it right for the third time because I was not aware of some parts alignment.

I Removed the two wires from the old relay. I Then pulled the old relay off the compressor. Next, I had to get the overload seperated from the old burnt relay, which took some care not to break. The old relay and overload is in a plastic compartment. Then I followed the directions that came with the new relay. The only confusion came with getting the two wires back onto the terminals of the new relay, mainly because the old relay was burnt so badly I didn't have any idea how it was originally wired. I crossed the two wires on the terminals of the relay. The compressor would click off and on, but would not start blowing cold air. I swapped the wires on the terminals and it started working immediately.

I don't know anything about repairing a refrigerator - I'm a computer tech. I noticed that the outside of the fridge was warm to the touch and the inside was not getting as cold as it should. I took the lower back panel behind the fridge off and noticed that the fan was not spinning. The local parts dealers did not have the condenser fan motor that was needed but they did say that they do go bad. I decided to order one from PartSelect.com and do it myself. Using a 1/4 inch nut driver and a flat head screw driver to pry the old motor out of the casing, I got the job done in about an hour or so. It's a relativly easy job. Besides the ouside panel screws, there's 3 screws on the inside near the fan blades you have to reach in to get. Pop out the whole assembly, unscrew the nut that holds the blades on and pry out the old motor and replace.. Try it yourself and save a couple hundred bucks!

getting it apart wasn't to bad. except when the small part that functions with the door flap fell out before i could see how it was installed orginally. after a few moments of trail and error figuired it out. previous messages you had posted from other customers helped alot, especially the gentleman who said screws were left handed made a big differance in getting it apart. glad you had the part.
works great.

Removed about 6 screws. Replaced the solenoid and door kit. Replaced the screws. These parts were easy to replace. They were also super easy to identify and order from the site. I received them two days after I placed my order.
Thanks partselect.com!

UNPLUG YOUR FRIDGE BEFORE YOU START> First I removed the shroud covering the lights and controls in the top of the refrigerator side. This was the hardest part, actually. Their are two indentations on the back of the cover and it is really hard to pull that cover off. Anyhow, once you do that, their are two screws, one by each light bulb in the top of the fridge that need to be removed. Their are also three hex head screws that need to be removed, two in the front corners of the assembly, one in the center, back of the fridge. Take those out and the whole assembly drops down. In the back right had corner of the assembly is the adaptive defrost control. Unplug it and set it aside. Plug the new one in. Put everything back together and you are back in business.

Very simple. Matched female plugs with respective male color coded prong; pushed together then inserted unit in slot of freezer sidewall and rotated into position...job done.

followed the instructions provided and that's it!