Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The evap motor failed (no air movement inside of refrierater
Removed screws from cover tested for power to motor found power was on to motor but motor did not work. I went to your web site was able to locate part in about 5 minutes . Even with over night shipping the part came to about $50,00, far cheaper tha a service call would have been.
For the defrost control board, it is a really easy replacement on my model Maytag refrigerator, all you have to do locate the freezer/refrig, cooling controls in the main part of frig and remove the control knobs by pulling them of by hand, for the cover use 1/4 socket with a socket wrench or socket screw driver to remove the cover, after that you will see a panel cover that you have to unclip by hand and that is where your control board is located and at this point it's just plug and play. just reassemble in reverse order. I changed my overload relaywith start capaciter out also when I changed my defrost control board. To change the relay out, first remove the lower panel on the rear base of the frig. and this is where you will find the relay pluged into the round black compressor, simply unplug the old and plug the new in, it's just that simple!
This is a side-by-side refrigerator. The crushed ice wheel is part of the icemaker bin auger, and it began to fragment, popping pieces of plastic into the ice dispenser and on into our drinks. The manuf. manual had nothing about parts in it, so GREAT thanks to Partselect for their website!!! Now, to dismantle the bin and auger is simple on this design: remove the bin from the freezer and allow it to defrost and dry; there are two small phillips-head screws on the front underside of the bin, holding the front panel in place - remove these screws and pop the front cover off; you'll then see two small phillips-head screws holding the auger-cap in place - remove these and pull the auger cap out, along with the auger; using a small pliers, remove the nut from the auger at the auger-cap, then slide the auger-cap off; at this point you just start removing washers, blades, etc, from the auger - MAKING SURE YOU KEEP THEM IN ORDER - until you reach the crushed ice wheel; separate the wheel from its metal brace, slide the wheel off and replace it; gradually replace all the other parts in order, cleaning them as you go, and simply put everything back together. It helps to keep the exploded parts diagram at hand - available on the Partselect website. It was a snap. The ordering process was simply and the part was delivered to my door on the second day after ordering.
Ice Maker was leaking water and causing the ice to freeze into a block
First I removed the Ice bin, I then loosened the ice bin rail under the ice maker and removed the screw that attached the bottom of the ice maker to the side of the fridge. I unplugged the power to Ice Maker from the back of the fridge and unscreewed the two screws that secured the ice maker to the fridge. This allowed the Ice Maker to be removed from the fridge. To replace the new ice maker I simply repeated the steps in reverse.
Icemaker leaked water into ice bin causing a glob of ice
Philips head screwdriver and ten minutes was all it took! I removed the two screws that hold the icemaker assembly in place, then pulled it out a little and disconnected the electrical plug freeing the icemaker assembly. Then I snapped the external parts off my old icemaker assembly and snapped them on the new icemaker assembly. Installing the new icemaker assembly was just as fast and easy. I snapped the electrical plug into the new icemaker assembly, then screwed in the two screws. It was making ice shortly thereafter. Glob free ice! I'm glad I didn't call a repairman. I probably saved a hundred bucks. A ten year old could accomplish this simple and easy task. No wonder the Maytag repairman has time on his hands.
Ok, pretty easy repair when the parts are correct (first part was faulty, parts select quickly sent me a new one)
First is removal, these tubes are in there very tight, they can be pulled out but weaken the lines and it is not likely to work without severly stretching the line to the point of breakage, if you have to cut them do so carefully and take off as little tubing as possible as you need the length to feed from top to bottom.
Once you have cut all the lines, or pulled them out (I was able to get 2 out without cutting) then make sure the edges are smooth, attach the inlet valve to the plate and just push them tightly into the new valve making sure you route the lines correctly.
Turn everything on and run the water line to see if it works. If no leaks, screw it back to the refrigerator and you are good to go. Takes maybe 20 minutes at most.
I used board levers to do one side at a time.Kinda tricky, but you can hoist up fridge high enough to replace wheels. take your time think it out and be safe . Make sure you use saftey boards to support load to protect yourself==good luck A small mirror may help to see how the rollers alien in the supports.
The new Ice Maker Assembly arived in less than 24 hours. I was amazed that it came so fast.
I had already removed the old ice maker in order to get the modle number.
I just took two parts off of the old ice maker and quickly snapped them into place on the new ice maker. Then attached it to the refrigerator in less than 10 minutes. With in a few hours I had ice again !!!!!
The crushed ice agitator kept slipping out of the bracket.
With the repair parts ordered and received from PartsSelect.com, I was able to install a new Ice Bucket and the crushed ice agitator assembly. This simple repair has the refrigerator dispencing ice like new.
Freezer would get cold at bottom and some of the refrigerator. Took of freezer back panel and located freezer fan. Took a meter and saw power was getting to it, but not working. Removed fan and replaced with new on, working like a charm. Cold air was not circulating enough throughout the unit because fan was not working. It was not the thermostat or adapter control.
Remove bottom panel in freezer side to get access to the coil.Remove old heater element and defrost thermostat.Installed new hearter and thermostat.Screw back bottom panel re-start frige.
Thanks to parts.com showing the schematic the repair was very easy. Note if the buttons fro dispensing water/ice break you need to order two parts. 1. dispenser Facade and 2. Dispenser facade Insert. To replace do the following. remove the catch tray at the bottom of facade. remove the two screws on the bottom and gently pull bottom of insert out and down. Next unsnap the two wires on the selonoid switch. Next pull down on the harness connector from the printed ckt. Next remove small phillips screw that secures the ckt to the insert and gently pry the six plastic clips that hold the ckt to the insert and remove. Next, install the ckt into the new insert and reconnect the selonoid switch. Next, install the insert back on the door. Next, install the Dispensor Facade sticker over the switch buttons taking care that it is aligned properly. Thats it ready to use.