Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dryer was very loud and sounded like it was scraping
Took the back and top off of my front loader. I had checked on you tube for the problem and how to fix it and ordered the part. Just followed the directions on how to remove the old idle pulley and installing the new one. Dryer runs like new!
Remove top, front and drum. Top is removed by sliding a putty knife under the front corners and pushing the tabs back. Front is held with screws. Disconnect two electrical connectors. Rollers are easily accessible and changed.
Replaced the most worn drum wheel any lubed the belt tension arm pulley. The noise didn't go completely away. There are 4 drum wheels. I need to order 3 more wheels and the tension arm now.
Take pictures along the way. 1. Remove lower front panel using screwdriver to lift up on tabs on top of panel. 2. remove door 3. unplug moisture sensor plugs 4. remove lint trap 5. on back of dryer, remove screws holding upper lid 6. slid up lid forward just a small amount, its hooked in towards the front of the upper lid. you will need to do this so you can can remove two screws under the lid holding the front panel of the dryer on 7. remove the front panel screws mentioned in step 6. 8. Remove lower front panel screws 9. remove front panel 10. reach into dryer at the bottom and release tension from belt pulley, sliding the belt off. (make a note of how the belt is routed around the drive and idler pulleys) 11. slide out tumbling drum 12. with drum removed, use socket wrench and socket to remove old idler pulley. 13. install new idler pulley 14. reinstall tumbling drum 15. slide belt back around tumbling drum, looping belt around drive pulley and around idler pulley. 16. When belt is installed, rotate drum a few revolutions to ensure belt rides correctly. 17. Reinstall front panel 18 slide top panel back into place and secure with screws from back 19. reinstall door 20. reattach moisture sensor plugs 21. reinstall lower panel
Dryer motor bearings failed. Motor wouldn't start.
Disassembled dryer. That was the hard part. Figuring out how to get the top off the dryer so I could get the drum out took the most time. The end caps on the control panel had to be removed by forcing them outward to release the plastic catches. Then the bottom corner screws were removed to allow the panel to swing up out of the way. The top panel could now be removed. To gain access to the belt and tensioner the blower and ducting off the front of the motor had to be removed to remove the belt. Now the drum was able to be lifted out. The motor swap was a cinch with no wiring modifications required. Reassembly was the reverse, with the most difficult thing being tightening up the blower fan. This required putting a wrench on the belt end of motor shaft and holding it while reaching thru a narrow gap on top of the fan ducting.
I had two dryers, one was gas and the other was electric. The electric stopped heating. So I rolled out the gas dryer, but it was setup for natural gas and at this location, I only have propane. So I changed the jets to work with propane, in the process I broke the igniter, so I replaced that and that made the propane one work. Armed with the knowledge from that job, I took the electric dryer apart located the thermostat and replaced that and low and behold I have two working dryers. One for now and one for an emergency. I only have four screws left over!!!! Jim Cooke
The design of the dryer did not make the conversion easy, I had to disassemble the entire front end, top and remove the drum. The kit included a new spud that's it (22.00?). Anyway the gas valve is convertible from NAT to LP only requires turning a portion of the valve about 25 degrees. I managed with a screwdriver as I could not locate my snap ring pliers(just moved). The directions were spot on, read them through once before you start.
I followed the very informative video and wrote down step-by-step notes for myself. The repair went very smoothly. The only thing I didn't realize, was that the dryer has 4 rollers, not just 2 shown in the video. All are easy to access once you disassemble. I had to do it twice since I had to order 2 more rollers in order to replace them all. Also, the triangle plastic washers come with the roller, so you won't need to order them separately like I did. I also changed the idler pulley roller while I was in there since that has bearings too. Just as easy. I'm very happy with my quiet dryer! One last note: The new rollers are a bit louder than normal at first, but they quiet down very quickly as you use the dryer. It must be because they are brand new.
Took the front part of the dryer out, released tension on the idler pulley, took the drum out, and remove the old drum seal. Make sure you remove the old adhesive with sandpaper or wire brush. Put the new adhesive on the seal, not on the drum. Adhesive is very runny. Seal may need to be stretched to fit the drum. Set the seal on the drum, let sit a few minutes. Put everything back together.
