Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The much used, upper oven heating element burned out and needed to be replaced.
I pulled the range out, unplugged it and removed the back panel with a Phillips-head screwdriver. I then removed the two screws inside the oven that holds the element in place. I located the two wires on the back of the range attached to the element. I gently pulled off the wires using a pliers and then easily removed the burned out element. I put the ends of the replacement element into the respective holes, screwed them in and then plugged the wires back on at the back of the range. After replacing the back panel, I plugged the range back in. I turned the oven on with an oven thermometer inside, to test it out. I imagine I saved at least a couple of hundred dollars for the repair with this simple DIY, if not, the cost of a new double oven range!
The oven and ranges would not heat up and an F9 error was displaying on the Oven Screen.
So, the F9 error indicates a electrical power issue. First I pulled the oven out and verified I had 240 volts at my outlet.
Then I removed the fire panel over the terminal block and the issue was apparent. The nuts on the terminal block were corroded. This had cause the resistance in the connection to raise and burn up the wire to my oven plug at the terminal block.
I removed the whole back panel and everything else seemed OK visually.
1. I go new connectors for the oven plug, stripped the wires, and crimped on the new connectors.
2. The terminal block DOES NOT come with the nuts to connect the wire to the terminal block. Mine were so corroded they had to be replaced. So I went and purchased the correct ones and installed the terminal block and reconnected all the wires.
3. I applied some dielectric grease to the connections through out the process of reinstalling to prevent it from happening in the future.
Removed the large lower back panel of range (6-8 phillips screws) which holds upper control back panel in place. Removed upper control back panel (2 screws), exposing infinite switch electrical connections. At front face of control panel, removed (pulled off) control knob, exposing 2 phillips screws holding switch in place. (NOTE: A sleeve is on the switch arm or maybe remains inside the control knob). Look for this sleeve. Without it, the knob will NOT seize the switch rotary arm. Removed each wire connection individually, one at a time, installing it in the proper position on the new switch. Reverse all procedures to put things back together. A very simple, straight-forward operation.
It was really easy. It took about 5 minutes to remove the screws holding the back in place. Another couple of minutes to remove the switch, and a few more minutes to change the wires over one at a time. Then 5 more minutes to put it all back together again, and plug it back in, and it just worked. Really simple.
Turn off breaker in electric panel fore stove. Put screw driver into slots in front of glass top surface. Pry top up carefully until top pops up.Remove burner dial, remove two philips head screws holding switch. Lift top carefully and prop up.With new switch close remove wires from old switch one at a time and place on new switch. Place new switch back in place, securing with philips screws. Remove prop and carefully press top down until it snappes into place.Replace dial, turn breaker back on and try burner.
Burnner would go to high setting no matter what the setting was.
Shut off power at breaker box , pull stove away from wall , remove Phillips screws from back of range pull knob off of switch . Look to see how switch is oriented remove 2 screws that hold switch in . Remove one set of wires at a time and place on new switch in same location . Put back together in reverse order .
turn off all electric to the wall oven. removed the old broiler. replaced the new broiler and turned on the electric. checked the brolier one to see if it worked....it did thanks for the customer service for her help in finding the replacement part.
Removed oven door and rack. Removed two screws holding element. Disconnected wires to element. One of the wires slipped into the back wall of the oven. The range had to be removed from the counter and back panel removed to gain access to the element wires. Install new bake element in upper oven. Connect wires to element spade lugs. Install rear panel. Restore power at circuit breaker panel. Very important - aways disconnect power before starting work.
I slide the range out and unplugged it from the outlet. I removed the back of the oven ( 8 screws ) using a cordless drill and phillips bit then with a phillips screwdriver I removed the oven sensor (2 screws) then I installed the new sensor , reinstalled the oven back , plugged the range in , slide it back into place and that was it. This repair took about 10 mins and the oven works perfectly. Thanks !
Removed door from oven by pulling up at the first stop point after opening the door. Removed the outer shell by removing 5 screws. Disassembled the inner door by removing 6 screws. Be careful with the insulation blanket (fits in a molded portion of the inner door). Glass windows can be removed (for cleaning) via a couple screws. Old gasket/seal is held in-place via spring-clips; just squeezed each clip, pushed each thru their respective holes, and pulled off the worn-out gasket. New gasket snapped in-place by pushing the clips thru the respective holes. Reverse the process to reassemble the door. You can do this job in 15-20 minutes. Took us longer because it took some elbow-grease (and patience) to clean the crud off the glass windows.
Removed the approximatly 10 screws that hold on both the upper and lower pieces of sheet metal that cover the back of the oven. Removed the screw holding in the temp sensor. Unplugged and removed the old sensor. Plugged in and installed the new sensor (using one of the included adapter wires supplied with the sensor). Put the 2 pieces of sheet metal back on and plugged in the oven.
