Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Water Leak At Water Inlet To Tub
Contrary to info on your website, the bezel is removed by turning it counterclockwise. This misinformation wasted a lot of time. The bezel is difficult to turn. I used a home-built wrench: drive two screws spaced 3 inches apart through a stick of wood, projecting 5/8 inch. Engage the screws in the slot in the bezel and in the grill, and turn ccw. I cleaned the deposits from the surface where the gasket seals with white vinegar. New gasket and bezel fixed the problem.
We were told by a repair guy to buy a new dishwasher-about a $900+ cost to replace. Then a local parts place and Sears each quoted us $85 for the part plus $129 to come out. Found your website and bought the part for $17. Also bought a hard rubber gasket that fits on the bottom of the door for $8. The brackets that came with that last part were the hardest to install, but the gaskets took 15 minutes. We did glue another strip of the long door gasket along the area under the door lip. Works great! Saved over $800. You rock!
I read the instuctions and snapped it together just following the pictures...reading only when the picture was not enough information for me. My husband thought I pulled it out of the box already put togethr, he did not know I put it together.
Top blade assembly fell off because of broken plastic on spray arm mount
Installed the new upper spray arm mount. First I installed it backwards which made the blades not turn freely (rub against top rack basket). Turned it around and was good to go. I found it helpful to remove the top basket in order to do this. Note that this clip is gray while your dishwasher tines are white. This does not cause any harm.
Lower washer arm came loose- dispenser door would not stay closed
Replaced the lower washer arm retaining nut,bearing ring.and seal in about 3 min.The retaining nut had broken off inside - make sure to remove the broken piece-I used needle nose pliers. The dispenser took about 35 mins. Removed all the screws around the inside of the door and removed panel.Removed screws holding the dispenser and replaced.I took time to give the dishwasher a good cleaning(inside edge). Now my wife is happy.
Plastic parts on this Kitchenaid dishwasher suffer repeat wear problems from heat and chemical detergents. The retainer nut on the bottom wash arm split horizontally int the thread area, and during operation, the wash arm would rise up and hit the bottom of the lower basket so there was a worn groove in the wing on top of the nut and the dishes weren't getting very clean. Simple replacement, just screw the nut down. Also decided to replace the bearing ring right under the wash arm because it was getting pasted with white crust-like material from hard water and chemical detergent residues. I've dealt with PartSelect twice now, and they are fast and efficient. The online parts breakdowns are easy to follow.
Peeled off the overlay graphic. Cleaned off the adhesive residue completely using WD-40. Cleaned surface with parts cleaner for the new stick-on graphic overlay . Cover control buttons so they are now labeled clearly. Press stick-on applique in place & rub surfaces for adhesion.
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
remove the lower arm and pieces.. get the parts stacked in the right order and hand screw the retainer nut... done! I decided to spend a little more and replace the whole washer arm and I'm glad I did. My dishes are coming out clear then they have in years!! Ordered the parts Thurs morning... thought i might get a load or two done but when I opened the washer on friday it was obvious I was facing a weekend of teens having to handwash dishes! 15 minutes later the doorbell rang and there were the parts!! Woo Hoo!!
unscrewed sprayarm, removed bearing and seal, used PartSelect pic and description schematic to identify part numbers then placed order. Parts arrived in two or three days.
First remove front panel of dishwasher. Held on by 2 screws on bottom of panel. Remove the electrical connections from the dispenser. Remove the six screws on the dispenser and remove dispenser. Reverse steps to install new dispenser. Also remove rinse aid sensor from old dispenser and install in the new dispenser.