Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Following a brief power outage, it stopped producing ice. Harvester was at 6:00 with fingers frozen in ice cubes. Would make a batch if I freed the harvester and jumped the t-stat, but would quit again.
Unplugged refrigerator. Used nut driver to remove small bolt retaining wire cover on right side of ice maker. Removed wire cover, used flat head screw driver to depress side-rail clips. Ice maker slid out, unplugged. Timer module cover pops off easily. Three screws removed the timer module. Installation was reverse of removal. Had ice in less than an hour, bin was full by next morning. If you have a screw driver and know what it's for, this job should come easily.
coupling on water line thru freezer door cut due to moving Refg and having to remove doors.
Snapped the large end of the coupling onto the main line coming from the water source and snapped the other end onto the small line leading to the ice maker. Quick and simple.
Ice maker auger motor runs but wouldn't dispense ice
My Kitchenaid side by side freezer has an ice dispenser on the door that would not dispense ice. The electronic door opened and the motor would come on with a repeated clicking noise. The Auger would turn with a few ice cubes in the bin, but not under load. After ruling out a clogged chute, I figured that the motor was stripped. The rod that turns the auger is a hexagon shaped piece, much like a screw driver you would use with your drill. After years of breaking down ice, it stripped the hexagon key in the motor, and would just spin under load. Now, PAY ATTENTION TO THIS PART. I looked online for a repair and saw a very similar motor repair that involved taking off the front panel and electronics. I did this, and ran into a solid piece of plastic with no way to get to the motor. I then looked at the inside of the freezer door more carefully. About 2/3 down I saw a small panel held in place by four 1/4 inch hex nuts. What was a 15 minute job, cost me over an hour removing and replacing the front of the freezer. Anyway, the replacement motor fixed the problem without a hitch, and now we have ice. Of note, this is the second repair of this ice maker system, after first having to replace the ice maker itself. And, this the second Kitchenaid built in refrigerator of this model as our first had ice maker issues and was returned as a recall. It is only 5 years old.
This was a pretty easy repair...I removed the retaining screws and slid the assembly off its tracks. Disconneting the wiring hardness was a pain but after a few minutes I had that off (use gloves, it gets cold in the freezer after a minute)
Once I had the unit completely out of the freezer the replacement part took only minutes to replace.
Reversed the process putting the ice maker back in - a few hours later my ice buck was full again.
Turn off water supply too ice maker and unplug the fridge power. using a nut driver remove one bottom screw from the bottom, near the front. The other two from the side atop the ice mold. (loosen screws and ice maker will lift up and off.) I set the ice maker on the counter, snapped of the front cover by hand. using a phillips driver, remove two screws near the bottom corners.(they go through the circuit board into the ice mold) circuit board in one hand, other end of ice mold in the other, slowly pull apart about 1 inch. remove the silver colored "on, off" bar at the end by snapping the retainer out of the ice mold. (the silver bar stays with the circuit board end) Watch how the ice guide(white fingers stationary on side of ice mold) hooks too the ice mold on each end. swap ice guide to new ice mold, insert three guide pins on end into holes on the circuit board, while holding ice guide onto ice mold, watch rotation bar while inserting into motor.(it only splines one way.) when each piece is lined up, simply push together and reinstall two screws. snap circuit board cover into place. reinstall ice maker into freezer in reverse order.
removed screws that held the ice maker in place, then removed the cover (popped off) The drive element was easy to remove, three screws and it was out. I put in the new part and reinstalled the icemaker with the three screws that hold it in place. I never call Sears for any repair. They use contract help and I have heard horror stories about those guys!
ridiculous how a tiny plastic broken part required a full motor assembly replacement. that being said, i went online, found this website and easily identified the part i needed to order. i was impressed when it arrived within a couple of days. removing the old motor and replacing the new was a piece of cake...and i am NOT mechanically inclined,
I called the local Amana repair man, wanted $150 for a new ice maker because they could not get the part I needed. Found Partsselect.com and the part cost $17 with shipping. They saved me over $100. The repair was very easy too, just removed a couple of screws.
i took the cover plate off the inside of the freezer under the ice bin[two screws] then I disconnected the wiring harness, then removed the four screws to remove the motor and then put the new motor in and the ice dispenser dispensed ice. Less than 1/2 hour with only needing a nut driver,and a flashlight.
Remove the unit cover by unsnapping from the bottom. Remove the face plate on the switches. The ice door simply snaps off the closing mechanism. The problem I have is that the original door included a heat trace element (keeps the back of the door warm to limit condensation). The new part was simply a new seal. I clipped the leads to the het trace (turn off the fridge before you do that) and put in the new door. When the heat ids on in the house there is no problem with condensation but on warmer days its pretty bad. I cannot find a replacement part with the heating element and have contacted Whirpool. THey haven't responded as of yet.
Our unit is a built-in unit so first had to remove the decorative cover panel to expose the internal on/off switch. Turned off the circuit breaker. Disconnected the wires (simple pull-off/push-on). Removed the old switch which meant clipping the plastic tabs holding the switch in position. Inserted the new switch by simply pushing it through the opening being sure to have it in the same alignment ('off' to the back of the unit.) Reconnected the wires making sure to have a white ground wires on the left and the black 'hot' wires on the right. Turned the circuit breaker back on. Turned the switch on. Now it runs.
Just replaced the switch, but unfortunately that was not the problem; nor was it the bulb....so I am back to square one. But Parts Select is a great place to order from. Thank you.
Ordered the parts from Parts Select and had them within two days (lightning fast shipment--and with just standard shipping). Disconnected the power to refrigerator, removed three screws from each cover panel, pulled the panels loose from the freezer wall, disconnected the wiring harness on each, removed the screws holding the two boards, replaced the boards with the new ones, attached boards to cover panel with screw, reconnected wiring harnesses, replaced the three screws on each side, restored power, and made ice! Whole job took about 15 minutes.