Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Remove and replace charcoal filter
Open microwave door and remove plastic cover running across top of the oven box by unscrewing 3 Phillips head screws above and behind plastic cover. (4th screw to the right is not related to this cover). DO NOT PULL COVER STRAIGHT OUT. Cover slides either right or left then pops out. Remove old filter and replace and reinstall cover. Filter lays at a 45 degree angle against metal tabs tilting toward you.
I was surprised to find that the turntable for my 10 year old GE Profile microwave/convection oven was not readily available at my local GE retailer. I ordered the part from this website hoping that my order would be filled. I received an immediate response from customer service and the part was on my front doorstep in under 1 week! I would order from this website again!
The microwave had been mistakenly turned on with nothing in it and the turntable coupler was badly burned. Pieces of it eventually broke off.
The burned remnant of the coupler was a bit difficult to remove. I did so with a pliers and also used the pliers to clear out some burned fragments of the coupler. With a flashlight I determined that the slot for the coupler was now clear. I matched the configuration of the slot with that of the new coupler and it slid immediately into place with no difficulty whatever.
put the other pieces into the new frame and put the door back on the microwave; getting the glass seated in the new plastic frame was a bit tricky, but the rest was easy; your on-line diagram certainly helped, but some specific directions with the part would have been useful; fast delivery was appreciated
open microwave door remove 3 screws on top of microwave, slide top panel to the left and pull out top panel slide old filter out put in new one and reassemble
I removed the main cover ( torx security bit required) and tested the magnetron, capacitor, diode and door interlock switches according to instructions found on the internet. The capacitor and diode tested good but the magnetron looked burnt and corroded on the tip. The magnetron I received was an exact replacement for the original. It was easy to replace the magnetron which arrived in 2 days standard shipping. I also cleaned the fan while I had access to the inside area. Hoping to get another 18 years use from the microwave!
Frost build up on bottom to ice bin and delivery chute in door creating ice blockage
Remove the ice bin. Turn the ice maker selection to "OFF" Use small flat blade screwdriver to open the plastic ears on the electic plug in connectiion Use #2 Phillips screwdriver to remove the screw on the front left side of the ice maker Pull the ice maker forward until free of the two studs in the left side rear of the freezer wall Check to see if the supplied water chute is the correct size for your application, if not remove the water chute from the old ice maker and place it on the new one. Place the new ice maker in the freezer connecting the slots on the left read with the studs on the left wall NOTE; IF THE ICE MAKER DOES NOT APPEAR TO BE LEVEL HORIZONTALLY REMOVE IT AND CAREFULLY REINSTALL IT TO ACHIEVE LEVEL NOTE: ENSURE THE WATER DELIVERY TUBE RESTS IN THE RECEIVER TRAY Reconnect the electrical plug ( needle nose pliers may be helpful in aligning the male plug with the female plug) Move the selector from "OFF" to "ON" Replace the ice bin and close the freezer door
When removing a non-working door switch, you will see a hooked piece of plastic on the holder locker that looks like a latch. If you try to pull it back in order to either remove the bad switch or install a good one, it will likely break. Instead, you need to pivot the switch (It pivots on a little post which is fitted into a hole at the corner of the switch) out of position so that it is not held back by the 'latch'. Then lift the switch out. If you have to use lots of force anything, you're doing something wrong. Reverse all this when installing the new switch.
The Microwave was making a loud sound when the vent was turned-on
I removed the microwave from the wall and observed where the sound came from, I then removed the part that was held by two screws, then I order the part on Part Select it took three days to receive the part and in 5 minutes I installed it.