Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
No istructions included
Although the parts did fit, some modification was needed to remove the excess tabs as it appears these parts were for multiple applications. However the end result was a good fit and reapirs were successful.
I was a bit hesitant to perform this repair but attempted it due to the other write-ups which were very helpful. The repair went very well and was quite easy. There was a suggestion to remove the gas defuser (the pipe thing that has the igniter attached), I believe loosening this defuser made the whole repair so much easer and quicker. Trying to remove the two screws that hold the igniter without this approach would have been very difficult. I was hesitant to do this but removing the 3 screws that hold the defuser in place was not a problem at all.
Oven igniter failed; electrode has been spotty for years.
STOVE Much easier to perform than expected. First, pull the plug. Second, lift door off hinges and remove bottom storage door. Then remove bottom tray (2 thumbscrews) and the head spreader below that (1 screw). Now disattach the two wire nuts that attach the igniter to electric (from bottom, where door was). I guess this has been changed once. If it had not been, might have had to cut these lines. Then, back inside the stove, remove the flame delivery tube or whatever it's called. It kind of twists as it pulls up. From there, it's easy to disattach the igniter with a wrench and then reassemble all in reverse order. Hardest part was getting one of the wire nuts to take. One of the replacement ones just did not grab, so reused one of the preexisting. OVEN Only hard part was getting the stovetop to release. Take off all the burner guards and such. Then lift the top slightly to locate the two push clips. Push each back in turn with a screwdriver, and this releases the stovetop, which rises up until it rests on two rests. Piece of cake to remove th electrode and attach new one. All working fine!
layed the range on its side and removed the gas valve installed the new valve leak checked and tested works like new. Great service and parts availability, shipping was fast.
Removed oven base plate by removing 2 screws and lifting out of oven. Pulled out bottom drawer and disconnected two wires from igniter. Removed 2 screws connecting burner to oven wall. Back to oven inside, and removed screw holding burner to oven bottom. Took burner out if oven. Removed 2 screws securing igniter to burner. Secured new igniter to burner. Reversed steps to put all parts back. Oven works fine.
1. Removed oven door. 2. Removed shelves. 3. Removed oven bottom. 4. Removed pan drawer. 5. Removed the 2 burner mounting nuts at back of oven pan drawer opening. 6. Removed top burner nut. 7. Pulled igniter out from top. 8. Snipped igniter wires. 9. Removed igniter from burner 10. Attached new ignitor wires with the enclosed wire nuts. 11. Attached new igniter to burner. 12. Replaced burner. 13. Pushed excess wire out of the oven through opening at back of pan drawer. 14. Reinstalled burner mounting nuts at back of drawer. 15. Reinstalled burner nut at top of burner 16. Reinstalled oven bottom, oven door and pan drawer.
Removed spark module only two small nuts. Inside was six wires on terminal. Removed one by one and connected right to the new module. Easy job 10 minutes and finished.
gas range and ignitor would not work on one burner
replaced ignitor switch between top burner knob and burner valve. Removed two screws from the top of the front panel and 4 screws from under side of front panel. removed panel and ignitor switch. slipped new switch on to valve stem reinstalled panel. ignitor works fine. You do not need to disconnect any gas lines to do this repair
Unplugged the electrical.Removed the door, removed the oven racks and removed the bottom pan. Removed the wire nuts from the two wires. Removed the burner tube. Removed the Igniter. Installed in reverse order. It was very easy however it was the third igniter that I had to replace in this range so I was used to it.
Replace Oven light socket and light bulb in kitchen Range
1) Turn off power at circuit breaker panel 2) Slide out Range from wall 3) Unplug Range 4) Remove back panel and unplug electrical connections to socket 5) From front of oven, remove glass cover over old oven light bulb and remove flange that holds socket and bulb 6) Remove old socket from mounting flange and discard. 7) Place new socket into mounting flange 8) Screw mounting flange and new socket into the oven from front. Reattach electrical connections from back. 9) Screw in new light bulb from front 10) Replace existing glass cover over new light bulb and snap wire holder in place 11) Replace back panel 11) Plug in range 12) Slide range back to original position 13) Turn on power Works like a charm! Thanks for having the parts after 30 years!
