Models > JCS66 > Instructions

JCS66 General Electric Range - Instructions

All Instructions for the JCS66
46 - 60 of 82
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
burners were burnt
replaced
Parts Used:
Drip Bowl - 8 Inch Drip Bowl - 6 Inch Trim Ring - 6 Inch
  • John from Brookhaven, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
old and rusted rings and pans
lift stove eyes and replace
Parts Used:
Drip Bowl - 8 Inch Drip Bowl - 6 Inch Trim Ring - 8 Inch Trim Ring - 6 Inch
  • Bradley from Gate City, VA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old trim rings were rusted and soiled
Too easy to describe. Just lifted out the old rings and popped in the new ones. PartSelect is my go-to source for appliance parts both for my home and my job as maintenance man for residential group homes in my area. Website is easy to use, prices are good, shipping is always surprisingly fast. Thank you.
Parts Used:
Trim Ring - 8 Inch Trim Ring - 6 Inch
  • Stephen from Bridgton, ME
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The control knob stem broke off when I moved the stove.
I located and removed 2 sets of hex-head screws under the front lip of the cooktop, then lifted the entire cooktop to access the burner controls. Removed the wires and taped them, and took out the old control after removing 2 phillips head screws. Installed replacement part easily. Only tricky part is that the various shaft adapters don't quite work with my knob. I'll fix it completely with a bit of epoxy and the adapters they sent.
Parts Used:
INFINITE HEAT SWITCH KIT
  • Jonathan from Harvard, MA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
3 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old drip bowls could not be cleaned
Replaced drip bowls.
Parts Used:
Drip Bowl - 8 Inch Drip Bowl - 6 Inch
  • Karl from Kempner, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
dropped & broke the oven light bulb cover
popped the new one on!
Parts Used:
Light Cover
  • joseph from san jose, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
I needed new trim rings around the stove burners
I logged into GE's website, put in my stovetop's requirements for size and type of trim rings, and was taken to partselect's site where I found what I needed. I ordered it and it came in less than a week!
Parts Used:
Trim Ring - 8 Inch Trim Ring - 6 Inch
  • KoLynn from Tempe, AZ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
drip pan, trim ring were old and burned
just replaced the old for the new
Parts Used:
Drip Bowl - 8 Inch Drip Bowl - 6 Inch Trim Ring - 8 Inch Trim Ring - 6 Inch
  • Preston from cincinnati, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
instructions could be better
it was hard to figure out the instructions from A switch to B switch to my switch. The first switch was no good the second one was good. prayer book didn't hurt.thank
Parts Used:
INFINITE HEAT SWITCH KIT
  • WILLARD from GLOVERSVILLE, NY
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
0 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
I needed new Drip Pans
I purchased a set of drip pans at the store only to find out that they were not for GE Ranges. I got on line and inquired and your representative was very helpful. The repair was easy. After cleaning the stove I removed the old drip pans and installed them one by one. No problem!
Parts Used:
Drip Bowl - 8 Inch Drip Bowl - 6 Inch
  • Gloria from San Jose, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Condo Had Very Old Drop In. Threw Away Drip Pans And Rings
Placed new ones on range. Exactly what I would do to wash them.
Parts Used:
Drip Bowl - 8 Inch Drip Bowl - 6 Inch Trim Ring - 8 Inch Trim Ring - 6 Inch
  • Valerie from Ogden, UT
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Burner constantly heated
Good directions
Parts Used:
INFINITE HEAT SWITCH KIT
  • Clifford from New smyrna beach, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Threw away old parts!
Put bowl in and then slid rings around. Just like cleaning procedure. Easy. Thanks for your service.
Parts Used:
Drip Bowl - 6 Inch Trim Ring - 6 Inch
  • Valerie from Ogden, UT
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Front Burner,no control of.
The original controls were different for the small burners and the large burners. The replacement part fits all. Before removing wires, pay attention to writing on new and old control and replace 1 at a time. The hardest part was being sure to cut the knob stem to the correct length. Control works well.
Parts Used:
INFINITE HEAT SWITCH KIT
  • Joseph from Baden, PA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Range purchased in 1989. Broiler Element Support Broke.
Removed 2 sheet metal screws. Threw away old part. Replaced with new part secured with the same old sheet metal screws. Works perfectly. Actually it took longer to type this response. I was very pleased with Part Select. If I need another part you'll be hearing from me.
Parts Used:
Broil Element Support
  • Ronald from East Greenwich, RI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the JCS66
46 - 60 of 82
Back to Top