Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Original terminal block plastic shielding melted, protecting appliance when the wires overheated.
Safety first * Unplugged 220 VAC from outlet. Removed shield cover screws with 1/4" hex nut driver (5 screws). Removed all 6 silver screws from terminal block with 1/4" nut driver, freeing all wires. Removed the green ground screw and ground bracket from center terminal. Cut away (using the drill) melted original terminal block plastic to access the 2 black 1/4" nuts holding original terminal block onto appliance. Discarded the original damaged terminal block. Attached the new terminal block, aligning the mounting holes and the terminal block the same way the original terminal block was lined up and re-used the black 1/4" nuts (original used because the replacement package did not include new black screws). I bought a new appliance cord, since the original cord overheated. Reattached all wires using the 6 new silver screws. Start with the middle terminal by attaching the appliance wires and the ground bracket. The ground must be attached to the bracket and the bracket bridges between the terminal block and the range body. Reattached shield cover. Plugged in appliance. Note: it doesn't matter which outside wire attaches to the outside terminals (both are hot), but the middle wire (neutral) must attach to the middle terminal. However, the ring terminal should be flush on the terminal block so you don't bend the ring.
Actual temperature in oven was not consistent with the temperature setting
I am a 69 year old woman. I watched the Repair Clinic YouTube Video before I started. I then pulled stove away from wall and unplugged it. Took off oven door and removed the top oven rack. Loosened and removed the screw holding the temperature sensor located inside at the top center back wall of the oven. Pulled the sensor through the opening until the plastic plug came through. Unplugged and removed it and plugged in the new sensor. Fished it back through the opening. Replaced the bracket to the back wall of the oven and tightened the screw. Replaced the oven rack and stove door. Plugged it back in and moved it back into place. I turned on the oven and let is heat for over 30 minutes and the internal temperature was correct with the setting.
I removed the 4 hex head screws holding the control panel , then the other 4 slotted screws. Disconnected all wires being careful to keep track of the color coding. Had a little trouble with the adhesive holding the face plate( I don't know why they even used it). Put the new panel in and reconnected it. Re set circuit breaker and tried the oven. It still wouldn't heat. it wasn't the control panel, but a burned out wire connecting the element in the back of the oven. Well, anyway I learned how to do the job and the the new panel activates better, so all was not lost.
1st replacement part was damaged from Shipping. Parts Select sent a new one that i received in only a few days. our stove is slid into a granite island so the disassembly was not as simple as most. It was necessary to remove the controls, the controls housing & screws along the top of the oven door. Within an hour the stove was back in place and working perfectly. Great service from Parts Select
The oven did not get up to or hold the correct temperature
This should have been a very easy fix. But, as I tried to pull out the old temperature sensor, the wire would not come out. I was afraid to pull too hard because I did not want to break the wire. So, I coxed it out easily until I could see the plastic connector. Then, the old wire pulled free from the connector leaving the end of the connector inside the back of the oven. I then had to fish the end of the wire around with the piece of wire through the very small hole in the back of the oven. Once I got it close to the hole, I was able to grab the connector with some needle nose plyers. Connecting the new sensor and reinstalling everything was easy and the oven now works just fine.
The bake element burned out. The gasket was dirty and not working well.
Replacing the gasket is easy and requires no tools. Pull out the ends that are just inserted in their slots. Then work your way around the door pulling out the little metal clips from their holes. Replace the new gasket the same way.
It's even easier to do if you remove the door first and place it on a table--but it's heavy. To remove the door, flip up the hinge clips--you might need a flat screwdriver to do this if they are old and stiff as mine were. Then close the door almost all the way--you'll feel a stopping point-- and pull up. It comes right out--but again, it's heavy.
Replacing the bake element is not much harder. It's easier to do with the door off, but not impossible with the door on. First, pull out the range and unplug it. Then, remove the hex screws holding the bake element against the back wall. The element has two electrical contacts that insert into clips at the ends of wires. Pull out the wires a bit to give yourself some slack, then pull the contacts out of the clips. Insert the clips from the new element into the wires and replace the screws.
If the wires get lost behind the back wall of the oven, it's not a big deal. Just remove the narrow central panel on the back (it has six hex screws) and push the wires back through the wall opening. Then replace the back panel and install the new element.
blew out board by crossing wires..mistakenly toke out bulb assembly to replace bad bulb
Turne off power to range..pulled oven out..Took top back panel off with nut driver. 4screws .. Took picture of control board....removed bad control board with Phillips driver...4 screws....installed New board...removed 1 connection at a time and replaced in New board..Turned power on to test new board...check picture to make sure connections are correct...turn off power...put back panel back on...put range back in place...turn power back o n...done ..approximate time 15 to 20 minutes..
old oven racks were ruined from self-cleaning oven
My exact model number did not appear in the listings, nor were the oven rack measurements clearly stated in items offered. I sent an email to customer service, received an immediate response with the correct answer (re: which part would fit my oven), ordered this item, and had a shipment arrival within days. The racks are a perfect fit, and they look great. The price is less than any other site I investigated.
Large right burner would only light in the outside and would not stay on
Ordered the part. Received the box damaged and did not realize the part was damaged until our son came all the way from Columbus Ohio to install it. We ordered another part which came in a timely manner. Even though I reported the problem and told them that we are not very computer literate they still would not accept that the part was damaged until we sent a picture. Our son came back from Columbus to install the new part which took about an hour. He took pictures which I was then able to send. They then asked for a serial number. I had already sent all the numbers from the part but that is when they said they wanted the serial number from the stove. We are elderly and getting that required me getting on my hands and knees to get it near the floor. Luckily I was able to get up. After multiple emails I now have to send the part back. Good luck to anyone working with this company. I will be waiting for them to reimburse me for the defective part.