Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dishwasher would not drain properly
On this model the panel under the door can be removed by unscrewing two hex screws on the upper panel and two phillips head screws on the lower vent panel. The drain solenoid is located on the left side of the pump and can be accessed easily without pulling the dishwasher out from under the counter. The solenoid is held in place with two phillips head screws, and the plastic actuator that is attached to the valve stem is simply press fitted on and held in place with a retaining ring. All necessary parts are included in the repair kit.
In replacing the upper rack in our dishwasher, I struggled and broke one of the end caps (see previous tale of woe. With the new end caps, I finished the job in less than two minutes with no tools. BUY END CAPS when you order a rack!
At first, I found a metal band that was rusted and loose, replaced it but still had a leak. I went to the diagnosis section and identified another area of problem, ordered the part and got super quick delivery. With the help my wife I was able to pull apart, repair and get the unit to run and stay dry. Wife is happy because she loves the décor of our old but now dry dishwasher.
Remove lower rack from dishwasher to provide easy access to spray arm/hub assembly. Removed hub/spray arm assembly from base of dishwasher by unscrewing it from the base of the dishwasher. You should be able to do this by hand. Then unscrew the upper spray arm from the hub. This is the telescoping tube that pops up from the center, and it is reverse threaded, so loosen it like you're tightening it.Remove the Phillips head screw holding the spray arm to the old hub. Transfer the upper spray arm assembly to the new hub. Screw the whole assembly back on the threaded connection it came off of. Hand tighten only.
The initial problem was that the top rack was difficult to slide out. I purchased a new set of upper rollers. In order to remove the roller you must slide it off the rail. To do this, you must first remove the end cap. I broke the end original end cap trying to do this. The new roller installation was simple. So was the installation of the new end cap. Simply press it on.
Read Joseph from Livermore, CA for good instructions. I took a camera phone photo for reference before I started. Should have taken another photo half way thru. Probably put the push-on-nut on backwards as it didn't 'lock' in - had too much play in the shaft, would have leaked. Impossible to get nut back off in good shape. I put original mangled push-on-nut on also - it added enough tension to eliminate play in the shaft. No leak..but lucky. Go ahead, you can do this repair for under $20.
Original part no longer made. Substitute too small by a half an inch. Corrected the problem by removing the 4 corner wheels from the old rack and put them on the new one. Now, it fits and works perfectly.
Washer didn't clean properly in either the upper or lower racks.
I didn't see any obvious defects in the washer like a plugged drain or obstruction in the pump intake, so I decided to try a new lower spray tower. I loosened the tower with a large pair of channelocks (arc joint pliers) by grabbing it near the base. The unit unscrews in the normal manner, i.e. counterclockwise. Once it's loose, it can be removed by hand. Thread in the new tower and snug it down. Done. Cleaning problem solved.
Removed and inverted the DW. Removed the impeller, grinder, screen and seals then the actual shaft seal. Replaced with new parts in reverse order. Instructions provided with the seal kit were simple and excellent. They were right to the point.
Ordered a new basket it was a little large as I ordered the wrong size. I just broke of the tabs that held it in and now its perfect and larger !!!! Simple and great service !!!
Pulled out the old and rolled in the replacement. The easiest part of the repair was ordering from the PartSelect website and receiving it via FedEx Ground the next day. Thank you PartSelect. Even my husband could have been successful with this.