Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Refrigerator hot, freezer normal
Refrigerator was showing actual temperature of 80 deg, freezer was about 3 deg high. (house temp was 65 at the time) Defrost heater seemed like the only component able to heat that much, so the defrost thermostat seemed like the likely culprit. I followed the installation directions in the video, and the fridge has been fine ever since.
Unplug the refrigerator. Pull all shelves out of the freezer. Remove light bulb shield and light bulb. Remove the two hex head screws on either side of the light bulb. Wiggle out the back wall. It is a tight sqeeze, but can be done. Locate the sensor on the top of the coils. It is held on by a simple clip. Wiggle the sensor and twist a little to take it off. Take wire cutters and cut the two wires into the sensor near the sensor to allow lots of room to splice in the new sensor. Strip about a quarter inch of wires left in the freezer. Use some sort of wire connectors, like twist caps, which will allow you to connect the two wires to the new sensor. Make sure to match the colors. I used shrink tube and line connectors. Once you have the new wires spliced together and protected with either shrink tube or electrical tape, tuck the excess wire out of the way and attach the new sensor. This is easily done by slight pressure on the sensor with the tube in between the clip and sensor. Make sure the wires are tuck out of the way and reassemble the freezer panel, light bulb, and shelves in the reverse order.
I watched the online video on how to replace a defrost limiter. It was almost exactly like my situation and made the job seem familiar. It was inexpensive ($8 part)and easy to do.
All the rest of everyone's post are all what I did. The only other thing I recommend is to put the back panel over the evaporator coils when your done. I replaced defrost thermostat, and heater. Once I initially completed it it kept icing over more than usual. You have to put the back panel back on so airflow goes over the coils.
My Ge top freezer fefrigerator was going into defrost mode and the heater was staying on for too long causing the food to thaw and eventually refreeze. Originally thought it was the mother board but after researching and do some troubleshooting of my own I realized the defrost terminating thermostat was bad. $8 part from Parts Select. Accessed the evaporator by removing back wall plate. Located thermostat and cut two lead wires to it. Spliced in new thermostat and reattached to eveaporator. Refrigerator seems to be good as new. There is an installation video on the web page that shows you step by step proceedure.
Once the part was received, it was very easy to snap the new part into place, and reinstall the drawers. No tools were required to complete the repair.
Frost buildup in Freezer, Fridge too warm. Fan running too long
According to PartSelect website, the probably cause was Temperature Sensor or Defrost Thermostat. I watched the replacement videos. . .. very nice and seemed easy. Ordered the parts and got within 3 days (nice!). I followed the procedure on the video for disassembly, I used a hair dryer to melt the ice buildup on coils and then cut the old Sensor and Thermostat out of the wire harness and, instead of using crimper to seal my new splices, I soldered them instead. I used shrink wrap sleeves, then wrapped in electrical tape for permanent insulation. My Fridge now functions like new again.Thanks Partselect! You are the best!
Open up the freezer make shore the fan is running/unplug the unit take out the Shelf,s take a 1/4 inch nut driver and take the back panel out pull out the ice box pull up on the back panel and pull it out to expose the coil it should be blocked with ice if it is take a blow dryer and defrost it unplug the fan and push it up. On top of the coil you will fiend the defrost timer take your hand and unstrap it and pull it out. Cut the wires and strip the wires back enough take the new part and wire nut the wires together and tape with electrical tape and put back on the coil. Put every thing back together your dun plug the unit in and wait over night if you can to let every thing cool.
The repair is a snap, you can watch the video and it will put you on the right path. My story is more about the service that Part Select gave me. I used a small box fan on low as a temporary fix. My model number was worn off from the box wine we store in that particular place. So I ordered the part based on looks, well it was wrong. Called Part Select and we talked, the nice lady on the other end said OH it must be this fan motor. Send us back that one, and I'll get this out too you. I'll credit your account for $7.99, and it cost me $8.99 to ship back the wrong part. Wow, the next day I received the new motor. They sent it overnight! I thought it would be 5-6 days! Unbelievable. I will use this company for any, and all my repairs.
The temperature in the refreezer and refrigerator was slowly getting warmer although the condensor motor was running continually.
Unplug the refrigerator and remove frozen food, shelving, light and back panel inside the freezer section to expose the cooling coils. The coils were completely iced over. Using a wet dry vacuum to discharge the air toward the coils quickly melted the ice. The trouble shooting section on your website described my problem and I bought both items which were the most common problem. Using the video(s) e-mailed to me when purchasing the parts provided great information regarding details for the repair. After replacing both parts the refrigerator is working great having spent just under $25.00.
