Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Leak from the bottom center
The connector pump had a pinhole leak at the seam (new part did not have seams). Also replaced the sump inlet which looked worn and the impeller.
Lay dishwasher on it's back to access the bottom. Loosen all clamps. Remove both U shaped holders on the sump inlet. Remove screws holding the drain motor. Pull out the pump motor and sump inlet. Connector pump can be unscrewed from the bottom.
Replace parts and reassemble. It isn't that bad once you start disassembly, especially for anyone somewhat handy.
I removed the screws on the inside of the door assembly, which allows the inside of the door to seperate from the outside. The escuchen (control panel) was easy to remove - the handle actuator is inside the control panel. The handle assembly was easy to take apart and re-assemble with the new handle and spring. I then inserted the control panel back into the outside door and reattached all of the screws with a power drill. This was a repair that a GE-authorized service tech told me was going to be over $540 - he claimed the control panel and door handle/actuator was a single assembly. In the end this repair cost me $14 in parts and 15 minutes of time. I complained to GE Consumer Affairs and they rebated the tech house call back to me in 5 business days.
This was a piece of cake. The original soap dispenser never worked right and always left unused soap. The new part was easy to install and works great. Only needed a 1/4" nut driver and philips screw driver to pull the outside panel and replace the module rinse and cap assy. Easy!
Hint on determining if the Main Conduit is the cause. Place a tapered flat piece of wood (wooden spatula) between the Main Conduit and rear of the dishwasher wall and remove any excess play. Run the wash cycle and determine if the noise goes away or is reduced.
Removal and Replacement of the Main Conduit Assembly: Opened the Dishwasher door and removed the lower and upper basket. The upper basket required the two rubber gourmets on the front of the rail to be removed by inserting a flat bladed screwdriver between the top of white farthest tab towards the rear of the dishwasher of the rack slide end cap (PS2370502 – Item 652) and twist the screwdriver while gently pushing the top of the tab towards the rear of the dishwasher and gently pulling on the end cap (The rear tab needs to clear the upper rack slide). Repeat this process on the other upper rack slide and remove the upper rack assembly.
Using a ¼ inch socket driver, remove the Main Conduit (PS651676 Item 585) screw located in the back of the Dishwasher wall and the screw from the upper spray arm (PS260547 Item 570) located on the roof of the unit. Remover the lower Spray arm by gently pulling up and turning it counter clockwise. Remove the fine filter hub nut (PS259078 item 454 ) by turning it counter clockwise and the fine filter (PS259068 item 452) The fine filter has a small tube going into the bottom of the dishwasher base that should be removed at the same time of the filter. Be sure to position it correctly when it is reassembled. There is also a small stainless washer in the bottom of the fine filter housing. Take care not to loose it during the assembly and disassebly process
Remove the Main Conduit from the plastic assembly in the drain of the dishwasher by turning it counter clockwise. (Note, the new Main Conduit Assembly comes with this part pre assembled). Remove the same plastic piece from the new Main Conduit assembly by carefully lifting the clip on it. Install the new piece back in the drain and tighten just prior to being pointed toward the back of the dishwasher. Reassemble the Main Conduit to the drain piece and tighten it the remainder of the way and reassemble all parts in the reverse order they were removed.
Part was an exact match. Make sure to use plumber's tape on all threads. Had to really tighten fittings to prevent leaks. Screws are a little difficult to get to. Test for leaks first, before final installation.
When I first tried to fix the handle I could not figure out where the spring went. I went back online and looked at the diagram of the dishwasher on this site and learned where it went. Once I knew where every piece went it only took me about 5 minutes to put it back in and another 5 minutes to screw the cover back on. I am a newer homeowner and want to be able to do minor fixes. This was my first one and was very happy that I was able to do it on my own.
I replaced the broken/cracked soap and Jet Dry dispenser (i.e. MODULE RINSE AND CAP ASM - part #PS1481889). (Water was leaking into the soap holder and hardening the soap into a lump before the door would open, rendering the soad useless).
Steps:
1) Unplugged the dishwasher. 2) Unscrewed the 6 screws holding the front stainless steel panel to the plastic door; set aside panel and insulation. 3) Unplugged two wires from small electric motor in broken ASM. 4) Unscrewed 6 screws holding ASM in place; easily slid out of door. 5) Slid in replacement ASM and put 6 screws back in (tightened snugly to make slightly warped door bend to new ASM). 6) Plug back in two wires into new ASM. 7) Re-attached stainless steel cover to door (having a 2nd person hold this in place while screwing would've helped).
All done - works like a charm! No more dirty dishes because the soap didn't work right...
Bottom line: If you have a phillips head screwdriver, you can do this repair. Easy to do.
Original gasket was old and had started to dry-rot.
Installing the gasket took about 45 seconds. It actually took more time to scrub the area clean prior to installing. One quick trick I found was to fold the replacement gasket in two, and use that mark to center the gasket and press it in from there. That way you don't have any guesswork as to how much slack to allow for when starting.
The cat brought in a rat which ate holes in the sump inlet.
First, I took off all the pipe clamps and retaining brackets. Then, I pried it out of there. One of the tabs holding one of the other bits to the body got busted, but it didn't matter, as it is held on very well just by the pipe clamp connection. I stuck the new one in and re-attached all the hoses. The GIANT complication was that a new floor had been installed over the old floor, right up against the kick plate- so in order to remove the dishwasher, I had to slice open the counter, as the new floor prevented sliding it out. To prevent the problem recurring, I spray painted over the sump inlet to make it taste worse. This is the downside of a cat door.
