Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Broken oven door hinge
I watched a You Tube video,removed and dismantled the door, installed the new hinge. I forgot to remove the small pin which is similar to a rivet. When I tried to close the door it bent. Eventually, I remembered the shipping pin and pulled it out with any damage. Believe it or not, I had read about the shipping pin on customer comments on PartsSelect...Good luck, it is relatively easy!
With a burst of flame the fan switch on our old Jenn-Air shorted out. Part Select had a replacement that fit and installed easily. Thank you for your prompt shipping! Bill Arendt
I turned the breaker OFF and attached the wires to the switch. I then reattached the switch housing to the stove top with the two screws and turned ON the breaker. The fan worked!
Rocker switch that controls vent fan would not work
First I removed the burner control knobs by pulling them off. Then I removed the screw washers from around the burner control stems. I lifted the chrome plate from around the burner stems. I disconnected the wire plugs from the rocker switch control. I made a note of which one was plugged to what (color coded). I removed holding washers from the two screws on the switch. Then I unscrewed the small screws that hold in the rocker switch and removed the old switch. I screwed in the new switch, put on the new holding washers, plugged the wire plugs back in, replaced the chrome plate and burner stem screw washers. Replaced the burner knobs and the vent fan worked. The hardest thing was getting the holding washers back on as they are too small to go over the screw but open up as they go on. I did not have the right tool for this so used a hammer and a socket with an opening that would fit on the washer so I could bang it down.
My daughter & I followed the instructions in your video and had fun repairing the door. The video showed exactly how to do the repair. I hope I don't need any appliance parts very soon but I will certainly pull up your web site if I do. Thanks for an excellent instruction video.
Both door hinges was simply worn out from 20+ years of usage.
Bought a pair for needed door hinges for replacement. Found a DIY video on You Tube showing technique to replace. Door removal was a bit awkward but hinge replacement and door reinstallation was as detailed in video. Could not nor would not have tackled this project without video. Premium quality parts sent and received within days of ordering. Wife happy therefore so am I.
My wife help take the door off. It was a little heavy . The door came apart very easy and went back the same way.We save over $300 by doing it our selfs.
Burn was full on or "high" at any switch position other than off.
Followed other's instructions from the web site: First - turned off the power at circuit breaker; removed two screws from downdraft vent area; pushed the switch housing back towards vent and lifted; held replacement switch next to defective switch and removed and replaced one wire at a time; loosed switch collar-nut and swapped defective switch for new one. Only issue was the "rat's nest" of wires gave very little room to work, especially if you have average sized hands.
Although only one side hinge had snapped, I replaced both sides with new oven door hinges. Followed the website video installation directions and all went well; the new hinges work perfectly.
It is so easy. Once I found the right size of filter from the website, I ordered it right away. It came in 3 days and I just need to take out the old one and insert the new one. No instruction is necessary. By the way, the price of the filter is one third of that from Jenn-air.
removed motor, saw that stablizers were broke and went to a local parts supply shop called SUNDBERG and was given a price of about 49.00 for three stablizers. at that point i went to the internet and found PARTSELECT.COM were i found the same parts for a fraction of the price,17.00, i could not believe it! SUNDBERG customer service was horrible.PARTSELECT custormer service is great and was just over the internet,any how the repair is done no more loud noise and wife is happy again ,for awhile.thanks keep up the good work.i tell everybody about you guys.
The original grease filter was damaged in our dishwasher (it is quite fragile) and needed to be replaced.
1. Remove the exhaust vent cover, located in the center of the top of the range. It just lifts off. 2. Swivel the clamp 90 degrees to release the filter. 3. Remove the filter and throw it away 4. Place new filter in place and lock in place by rotating the swivel clamp back 90 degress. 5. Replace the exhaust vent cover
Shut off power. Removed cover held in by place by two screws in downdraft area. Removed old switch, removed lens caps from LEDs. Placed switch on posts. Fastened switch to posts using my own nylon lock nuts (not included). Forced leads onto electrical nodes on switch. Put everything back together.