Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Remote drain pump leaking
First, I unplugged the washer then removed the front panel to the washing machine, then the pump cover, then the two hoses connected to the pump, draining them into a small bowl. I removed the ground wire and electrical connections.
Then I removed the two bolts holding down the pump and removed it. I had to pivot the hose connections on the pump to match the old one. Once I did this, I removed the hold-down bracket from the old pump and installed it on the replacement pump.
Getting the hoses clamped back on the new pump was a challenge, and I finally used an automotive clamp on the rear hose. Once the hoses were connected, I bolted the pump back in, reconnected the power and ground connections and replaced the cover.
Overall, it was a fairly straightforward installation and the only challenging part was the hose clamps.
The door latch was broken from opening the door before the end of cycle release.
I found and ordered a new latch from Partselect.com. After a few days I received the new part. I used a square drive screwdriver to remove the two screws that retained the broken latch, put the new latch in place, and reinserted the retaining screws. The job couldn't have been easier. I couldn't be happier with the quality of the part or the speed of delivery and wouldn't hesitate to order from Partselect.com again.
I removed the 2 screws holding the broken door catch in place, and attached the new door catch with them. The repair could not have been easier, and now the door works great.
Also, I ordered the part, and it arrived via FedEx the next day. That greatly exceeded my expectations!
Would go into high spin in regular wash settings .
(1) Removed top of washer . (2) Open washer door . (3) Removed the two screws holding the Door Lock Sw while holding the switch from inside the machine . (4) Lifted the switch up to remove wire harness one wire at a time and reconnect to new switch . Double checked work and reinstalled switch . (5) Run washer machine make sure everything is back working . I need to add that the washer door needed to be adjusted . The bottom of the door was kicked out . Washer is now working .
The door catch on the washer broke, and I had to epoxy the broken catch to finish my laundry. I looked for the part online, and PartSelect not only had the part but had a photo of it as well. I was very impressed with how quickly the part arrived, and within 15 minutes the repair was complete. Thanks for having the photos and getting the part to us so quickly.
No tools necessary. Simply turn old knob to the left or counter clockwise and it will disengage. Slip on the new part and turn to right or clockwise until it is tight. 2 minute project.
no problemO top loader. open top, disco two electrical plugs and a small hose, then remove two screws that hold valve in place and remove. Re install in reverse order. Thanks for your support Eliot in Alaska!
I followed the instalation instructions provided with new parts. Getting the mounting pins out was relatively easy However, the shock on the right, behind the pump, was a bit more difficult to remove than the one on the left. I took the rubber drain off the pump in order to get at the pin behind the pump. The new replacement shocks came with the plastic bushings inserted in the shocks in alternate directions. The original pins were all inserted into the bracket / shocks from the rear so when I installed the new shocks I reinserted one bushing on each shock so they we both oriented in the same direction. The instruction says to be sure the mounting pin is pressed from the side with the busing collar. It seemed strange the shocks came that way, with no mention of switching them. The most difficult part on the installation was pushing the pins back through the bracket and shock since there was no easy way to push the pins in from the rear. I used a large channel locks on the left side, but the right side was more difficult with all of the obstructions. I finally was able to push in place with my bare hands but was very difficult. Sorry to say the new shocks did not cure the vibration at all. I was very careful to make sure the machine is level. I'm not sure if there is a cure other than replacing the machine.
I started by removing the two screws at the back of the washer and taking the top off of the washing machine. Than I removed the two screws securing the door lok and switch assembly. I disconected the two or three electrical connections and install the new one in the reverse order.
pulled the retaining ring then unscrewed 2 screws removed the bad switch and unplugged the old wires then hooked them back to the new switch...this was the second switch in approximately 2 years...
The door latch was broken from opening the door before the end of cycle release.
First I tried to unscrew the two screws holding the latch with a phillips screwdriver. When it wanted to slip, I took a closer look at the screw heads and saw they were square drive. I got the proper tool and removed the screws, replaced the latch and replaced the screws in a few minutes.
(This is reply #2 of 2) After I finally got all of the parts (at least the rear brackets and screws) I found that the panel only had one of two holes for the two horizontal screws. After drilling a new hole in the left rear bracket position, I discovered that the 2 screws could not be threaded into the bracket pilot holes. Theyt froze up at the top of the taper in the threads. I had to increase the size of the hole 1/64" to get the screws in. There also is a trick to getting the bracket through the punched out hole in the panel- you must angle the bracket corner to corner then apply about 10# of preasure to the bracket to force it through the hole. Other than that, the panel install went pretty well. Now I have to get the front brackets and springs and screws which are on backorder...
