Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Drum Bearing slides were worn and broken, dryer made high-pitched noise.
First, let me say that my repairman said the bearing and slides would cost between $150-200, and the total repair would be pushing $400, so we should just get a new dryer. Well, the total cost for the parts was less than $50.
The installation was easy. 1. Remove the two bottom screws of the door hinges, loosen the two top screws, and remove the door. 2. Unscrew the two screws, under the upper lip of the door opening, that secure the front panel to the top panel. 3. Pull the front of the top panel up, and then pull the panel off. 4. Remove the bulb from the front panel. 5. Unscrew the two screws, from inside the dryer, that secure the front panel to the frame. 6. Pull the front panel away from the drum and frame. Had to lift the drum slightly to do this. The electrical connection wire was still attached to the front panel. 7. Slide off the old drum bearing from the inside of the front panel. 8. Insert 4 new slides onto the new bearing. 9. Slide the new bearing onto the rim of the opening in the front panel. 10. Reset the front panel back into the slots at the bottom front of the frame, with the bearing fitting into the drum. Again, had to lift the drum slightly to do this, and make sure the wire was not caught between the front panel and frame. 11. Re-secured the front panel to the frame with the two screws. 12. Replaced the bulb in the front panel. 13. Replaced the top, and re-secured it with the two screws. 13. Put the door back on. Quiet dryer once again! And saved the $800, including installation, a new gas dryer would have cost us!
The problem was intermittent. It only happened when the unit was first started. After it was restarted it usually worked until the load was dry. I looked at the schematics and saw that only the hi-temp therostat and the motor overload could stop the dryer completely. I put my volt meter on the hi-temp thermostat and ran the dryer. When the dryer stopped I realized the hi-temp therm. was tripping. I read the web site help for this symptom and the suggestion was the bias therm. I replaced it and the unit worked.
Having recently replaced the heating elements and main bearing on the dryer I knew how to take the thing apart, getting to the motor was easy. However, the fan side of the shaft was longer than the original so I had to bend out the metal front panel where the fan is located so it would spin without grinding against the front of the dryer. That done, the rest was easy to finish, mounting bolts on the motor tightened, one last test before putting it back together and all was well. The dryer now works better than it has for a long time.
interlock switch was bad. Prevents the dishwasher form running as it "thinks" the door is still open.
Opened door, removed screw holding down metal plate that presses against interlock switch when door is closed. Removed plastic cover thingy that is over interlock switches. Removed the interlock switch by pressing the plastic lock thingy away from switch. Pulled the wires off each end of the interlock switch. Removed new interlock switch from plastic bag and reversed above procedure. Done, shut door and the dishwasher works.
5 minutes! loosened 4 screws pulled front off replaced bearing, felt, and slides. put everything back together, tightened screws. Worked like a NEW ONE!!!!
I removed the door and "flipped" it to open right to left. Rather than remove the existing door latch I added the purchased latch on the right side to enable opening the door right to left or left to right.
Horrible screeching noise when the dryer drum was in motion, cracked pieces were tangling and ripping the drying clothes.
I removed the top of the dryer (unscrewed from the inside to release the top). Removed interior screws to pull open the front of the dryer. Once inside, it was really visible that the old parts (front air duct top and bottom) were in bad shape. They were cracked and broken. I removed the old pieces (they pretty much cracked and crumbled right off). I snapped in the new pieces careful to avoid damaging the electrical connections and wires. Once snapped into place (top and bottom), I careful put the front back into place making sure that the dryer drum rested on the new pieces. All screws back in place and all done! Dryer is now working as new!!!
Dryer developed a progressively noisy squeak over several months
I followed the directions that were listed on this site by other Do It Yourself individuals...by the way I'm a lady and more mechanically inclined than my husband, but he was a great help in lifting the drum up and out. (I unplugged the dryer before starting repairs) 1. I removed the two screws located at the top of the dryer inside the door. 2. Top of dryer cabinet lifted up after screws were removed. 3. Located and removed front panel retension screws and removed front panel and set aside 4. slipped belt off motor by reducing tension on idler pully 5. Removed screws inside drum that secured drum to bearing assembly 6. Husband and I lifted drum up and out of cabinet (this went very smoothly and took less than 15 minutes time. 7. Followed supplied bearing drum instructions and removed old bearing and installed new assembly. 8. Thoroughly cleaned out internal cabinet, blower, and motor areas 9. Reset the idler pully into proper position. 10. Tipped dryer on 'back' to reseat the drum With A NEW DRYER BELT (taped temporarily around the drum) into the bearing shaft (I may not be using the proper terms) 11. tipped dryer upright and while Hubby balanced the drum, the front panel was resecured to the rest of the cabinet. 12. Removed temporarily applied tape that held the drum belt in the general position, then using the rear access panel, I slipped the belt over the motor into the proper posisiton. 13. Top cabinet was reapplied and screwed into place. 14 Plugged in and tested the dryer...NO SQUEAKS and it works beautifully and quietly!!
The job is not terribly difficult, but I am only 5 feet tall and the drum is bulky to work with and balance. Reaching into the cabinet to slip the belt onto the motor stretched my arm to the limit. I found the cabinet reassembly and realignment of the screw holes quite annoying. But the total job proved satisfying upon completion.
Pulled out the remnants of the old latch out with the pliers and then popped the new one in...less than 2 minutes. Oh, and the part was delivered in less than 2 days. Great job, Partselect !
Removed the front panel,tiped up the top panel ,removed the drum, drive belt,motor and exaust tube assembly. cleaned and vaccumed all lint from every were. Removed motor from fan blade and houseing. Reinstalled moter and pulley that came with the moter and fan blade. reinstalled all of the rest of the parts and plugedin the wires. once all back together pluged into outlet and turned on and prasto works great.
my problem was easy, i orderd a new lint filter, for a dryer that is at least 10y/o. it came to me by FEDEX, in 3 days. i threw out the old one and put in the new one. easy peasy. i will say that this website had what i wanted and got it to me very quickly. good job by PARTSELECT......
Dryer not heating. When moving it away from wall it was sparking badly where the cord hooks up.
Removed case parts to expose internal wiring. Vacuumed up various types of mouse debris and plugged hole they were using. Ordered terminal block to replace the one that melted while sparks were flying. Replaced power cord with one I had in my basement from some other appliance that died a while ago. "Hey honey, ya know those old parts I saved..." :) Now it is heating to capacity and no spark-show! Oh yeah, the part I ordered from Partselect.com was delivered to my door the next day!!!!! Wow!
When I went home at Christmas, I saw that my Mom had been using a small bench to keep her dryer door shut. I wrote the make / model of the dryer down and found your website. I ordered the part, and my sister snapped it into place. My mom was so happy to have her dryer door stay shut again!