Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
dryer wasn't getting hot
1. removed two screws to take off top. 2. removed two screws to take off front. 3. Took belt off pulley and removed drum. 4. inspected old heating element at back of dryer - saw broken wire 5. replaced heating element (round w/ heating coil) 6. Re-assembled dryer
Helpful hints: 1. mark down or take pictures of all wires before removal - easy to mix them up 2. when you re-attach drum-belt, it should be taught. Comes straight down wall around metal pulley and then forms an "S" as it wraps around plastic pulley on way up. To re-attach, stick both arms into dryer - one to pull plastic-pulley and other to attach belt.
Pryed off the top with a flat head screwdriver and removed the 2 screws holding the front panel to the sides. Then lifted the front panel off of the bottom brackets. Belt fit perfectly and followed the provided instructions to loop it around the motor and pulley. PartSelect got the part to me within a couple of days and the repair was a snap.
First I figured out it was the start switch, I heard it make an electrical zap noise when I turned it and then the dryer didn't start. Once I had the part I simply removed the back from the dryer with a screwdriver (5 phillips head screws and 1 flat head). Then I twisted the old switch and it popped right out. Then I unhooked the wires and rehooked them to the new switch. Then I twisted the new switch into place, tested the dryer - IT WORKED! After that I just replaced the back cover and I was done. It was so quick! I am a 25 year old single mother with a 21 month and 4 month old. If I can do it on my own anyone can!
First, I loosened the the top control panel and then loosened the top flat roof panel which allowed me access to the inside of the dryer. Then, I removed the front panel which allowed access to the drum. I was amazed at the amount of lint that was inside the dryer itself. Most of my time was spent in the disassembly and cleaning of the internal cavity around the drum. I reached below the drum and removed the belt from the pulley wheels and then unscrewed the drum (from the inside) from the back of the dryer and bearing kit. I removed the diffuser and cleaned it thoroughly. Then I replaced the entire drum bearing kit - the old one was almost completely dissentigrated. I probably should have applied some kind of non-flammable lubricant to the new bearing kit - the instructions did not include this step but after about 3 loads a slight squeak (different). I put everything back together - applying the new drum kit will require 2 sets of hands (my 9-year old daughter did great at this). I re-assembled the dryer and it works great, again except for the slight squeak that's still there. I may disassemble it again and apply some lubricant but I do not know what kind to get; I need to check that out.
Deflector has 3 bolts attaching it. They require a star wrench. Had to purchase same to do the repair. Removed the bolts(they are sheet metal type screws(bolts). Installed the deflector and started dryer. Loud rubbing sound noted. Shut off and checked the drum and noted it was not running concentrically. Removed deflector and the found the 3 screws actually retained the drum to drive. Had to make alignment pins to allow proper alignment of the drive, drum, and deflector. Once the pins were used during installation of the deflector everything worked correctly. Turned on dryer and it operated normally. Had I had the proper tools the repair would probably have taken 30 minutes or less.
First I removed the removed the screws that held the top on the dryer. Next I removed the screws that held the controls on from the back. I then removed screws that held the left side in place and removed the drum by first removing the drive belt. The heating element unit was removed by removing four screws and the wiring harnes. I reversed the procedure to install the heating unit and put the machine back together.
Someone I'm related to by marriage accidentally dried a plastic-coated tablecloth on high heat, and our heat deflector was hosed. I was very happy to find this part here for such a reasonable price; Sears wanted about $65 for it. Installation required a Torx bit, and removing the old one was easy, but the dryer's design made it difficult to reinstall the heat deflector while keeping the dryer running concentrically. I ended up cutting the heads off three screws, threading those into the plate behind the drum, sliding the new heat deflector on over those, and then one by one replacing them with the original Torx head screws. Once I figured it out it didn't take long but it took me a while to figure it out. That's probably more a reflection on me than the dryer!
dryer would run until you shut it off , timer did not advance , clothes would air dry there was no heat
unplugged dryer ,pulled dryer front and top off and removed drum , found element wire broken . loosened element to be able to remove wire pods . reverserd removal ( belt is a little tricky ) reattached power cord to outlet worked like a charm.
The dryer began squeeking very loudly progressively getting worse
A very easy fix. Opening the front door to the dryer locate two chrome phillips head screws in the upper part of the door opening which hold on the top of the dryer. (I think in the older dryers the top simply was held on with keepers and you could simply pry it off. Not the case here)Lifting up on the front of the top it comes away from the back control panel. I would recommed that the control panel be removed as it is necessary to remove it to put the dryer top back on due to three clips that wont allow you to put the top back down with the control panel in place. It takes a star wrence to remove it. Once the top is off ther are two phillips screws holding the front of the dryer on (one on each side) remove them and the whole fron lifts up and off. The drum rides on a plastic schroud attached to the dryer inside front. Mine was so worn it required the purchase of the entire assembly which comes in two parts. The upper part had worn away so badly the drum was riding on the metal causing the noise. I ordered both the upper and lower assembly and both just simply snap off and the new ones snap right back on. No tools. I was a bit dissapointed as I assumed that the felt which is located in the lower assembly would come with the new part however it did not nor did some plastic tabs which the drum rides on in the upper assembly comes with the replacement part. It takes four of those tabs so order appropriately. Went back together easily and the whole job was done in about 40 minutes.
Remove the two screws holding the top down. Disconnect two wires from door switch. Remove the two hex screws holding the front on. Remove the 4 screws holding the access panel on the back and disengage idler pulley to loosen the belt. Remove the drum. Label the wires then remove the heating element. Check orientation of ground strap before disassembling rear bearing. Remove four screws holding rear bearing to back of heating element. Install rear bearing and ground strap on to heating element. Reinstall heating element. Reconnect wires.
Most Important : Get help putting parts back on drum! I didn't and that's why it took over 2 hours. I will describe how I did it.
Unscrew bearing from inside of drum. Wrap screwdriver with tape to a little larger than the screw hole. Use small screwdriver to line up the drum, shim and deflector. Don't forget the brass shim. It wasn't on the parts diagram. Start two screws don't tighten them yet. Remove Screwdriver and start third screw. Tighten all three down. Put belt on drum. Install drum and belt. Reverse disassembly. When putting the front on make sure drum rests in the felt.
I rated this a bit difficult because I did it myself. With help this is a fairly easy repair.