Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
When I would run my dishwasher, water would pool on the right side front of the washer. It was even dripping down into the basement. When I figured out it might be the the front door gasket, I ordered the part.
The repair was very easy! I simply pulled out the old gasket from around the front part of the dishwasher. I cleaned the area with a damp rag from any residue that was left on. I bent the long gasket in half and and pushed it in starting at the center of the dishwasher and went down one side at a time until the whole gasket was in. I then ran a short cycle on the dishwasher to make sure it was properly in place and the problem was fixed. NO MORE WATER ON THE FLOOR! I was so very happy to know my problem was fixed and I didn't need to buy a new dishwasher! It's been running great! :) ~ Elizabeth ~
After 22 years of virtually trouble -free service, I could tell by the sound that something was wrong. Water fill ran too long. Float not stuck. Checked and found float switch stuck.
Very simple. Remove bottom panels. Remove one screw holding old switch in place. Move wire connections from old switch to new one. Cleaned and lubed the switch actuator. Mounted new switch. Checked that float and actuator worked freely. Left bottom panels off till I ran a load - just to be sure all was OK. Remount bottom panels...Done! P.S. Don't forget to turn power off to dishwasher any time you work on it!!
Removed dishwasher door liner and removed soap dish door latch assembly. Removed latch from assembly and replaced with new latch. Had trouble replacing assembly in correct sequence. Had to go on line and look at sequence picture to replace assembly correctly. Installed new gasket and replaced liner in door. The new gasket and latch solved my leak problem. Thank you PartSelect
I pulled out the old gasket and put in the new one. You need to stretch it a bit as you guide it in the track. It was very easy but did not solve the problem. Apparently, Maytag dishwashers are known for a leaky soap dish which I figured out after the door gasket was replaced. The problem is usually with the soap dish latch. You need to take the inner door off, disassemble the soap diehs, out a new gasket and latch on, reassemble, and you should be all set.
removed lower dish basket. then removed 3 screws lifted element cover and removed center hold down nut lifted spray nozzle nad installed new parts. dishwasher is working like new. thanks for asking.
Popped off the plactic screen filter (3 screws). Droped in the new Spary Arm and put back together.
You guys are AWESOME! I ordered the part on a Wednesday afternoon and received it Thursday morning. So all and all I didn't even have to wash any dishes by hand.
just unscrew the inside panel. using a torx screw driver. disconect vericarefully the bad actuator and install a new one. put back everything in back order .
Dishwasher was dripping water out the front during use
The dripping water was coming from bottom right side of the door, almost directly beneath the detergent dispenser. Looking closely at the drips, I could see that they were coming from saturated insulation that is between the inner and outer door layers. I took the inside piece of the door apart and sure enough I could see water had been getting through the door latch and running down the inside of the door. I could see that the grommet around the door latch was cracked and brittle, so I replaced it and was pretty sure that would resolve the problem. But when I put the door all back together and did a test run, I had a leak even bigger than the first, but this leak appeared to be through the door seal at the bottom right. I then ordered a new door seal, which took only 5 minutes to replace and resolved the leak. I think the old door seal was too worn out at that spot and just by removing and replacing the inside door layer, it must have not made a good seal at that point. But I recommend starting with the door latch and grommet first, since that is a $4 part, and then proceeding with the door seal, a $43 part, only if necessary.
first i unhooked the 2 hoses then removed the 2 screws holding the valve in place, I then removed the hose fitting from the old unit and installed it on the new one. I then bolted on the new valve and reconnected the hoses and it worked fine.
I determined that the problem was the door switch after disassembling the door and noting a broken electrica switch. After receiving the new part, I replaced the whole door switch assembly, and the dishwasher turns on and works fine.
I first replaced the seal/grommet around the soap dispenser latch, which was leaking, but did not totally stop the leak. I ended up ordering the door gasket too. Both were very easy to replace. My wife wanted a new dishwasher, but let me take a crack at fixing the leak first. Woo Hoo - big $$$ saved.