Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
First unscrew the two screws at top to disconnect the control panel. Lay unit on the back. Remove door(be careful not to lose washers and hinges). Remove four screws to lift off top. Wiggle drum, slip belt over drum. Replace door, then put Four screws back in place.Stand unit upright.Remove back panel, you should see belt hanging.Pulley wheel is in front of you.Follow instuctions sent with pulley wheel.Reattach you're ready to roll, make sure you sllip the belt on the drum until the drum spins.
dryer would make clunking noise and sometimes a scraping noise
I looked on the internet for instructions to take the dryer apart,took the parts out one at a time ,and replaced them.It was easy and it made the dryer quiet again.I could see the obvious wear on the parts.I was happy to save the money a new dryer would cost.
Actually, my boyfriend did the repair by taking off the top and back of the dryer to access the drum and belt he replaced the belt and put the dryer back together We are greatful for your service and really happy we didn't have to drive all over to find the part.
Pulled the top of dryer off. Separated the door from the drum seal or gasket, slipped the belt through, put the drive belt on the motor and then put it all back together.
dryer was making thumping noise (like when a pair of sneaker is being dried)
Started with removal of rear inspection plate on rear of drier,rotated drier drum by hand to look for any visible problems. Found that drive belt with age had lost sections of teeth and every time the bad sections would go past motor they would "thump". 1. Removed belt from tensioner. Done simply by moving tensioner to unload belt. 2. Slipped belt off motor drive and moved belt to front of drum. 3. Opened drier door and removed 4 screws from under the lid or top of drier ,raised lid for access to belt once belt had been slid to front of drum. 4. (steps 4 and 5 are the hardest parts)Worked drive belt between drum and felt insulators keep in mind there are many stamped steel pieces and sharp edges can be present. 5. Removed belt by feeding a small section past felt and drum and worked rest out from frt. top of drier. 6. Installed new belt in reverse order as removal. This was done without aid of instruction manual and by someone having major back surgery 4 months earlier. No idea how much this saved me but the price of the belt and time and effort involved made it woth my while I'm sure.
Removed the top, front and lower rear section of the dryer. This being my first experience replacing a dryer belt I naturally missed the tensioner pulley first try, then installed the belt on the wrong side of the pulley and found I didn't have enough tension. After some thought and a long hard look I realized my mistake and the third time was the charm. Next time I need to replace a dryer belt it should be a snap and go a lot faster.
Unplugged machine and turned off the gas. Removed top panel,4 screws along inside top edge of door opening. Used a wooden shim to pry the drum away from the surrounding "lip with felt padding. Slipped belt through.the trick is getting the belto around the entire drum. First I got it over the top of the drum, and fed it around the bottom by turning the drum and pushing the belt through the opening made by the shim between the bottom of drum and the lip with felt. It was kind of like feeding a bicycle chain onto a sprocket as you turn the wheel.. Removed back panel and vent hose, removed old belt laying on floor of machine, fed the belt onto the motor pulley and the tension pulley. Tension pulley presses on top side of belt. Belt should be in same position on drum as old belt, you can see a friction mark all around the drum from the old belt. Replaced panels and vent hose. Put felt padding back into place wherever it slipped out. Very important because if you don't it scrapes the drum when turned on and makes a loud sound. Dryer works perfectly again.
Just put it in place. The hardest part was to choose the model number closest to the one I have (since it wasn't listed). PartSelect.com showed a list of similar models and I was able to choose from that. Luckily I got the right one (wrong color, but it fit!).
The drive belt on the trusty GE dryer, bought used from a GI in Germany about 40 years ago and donated to our relatives when we returned to the States finally broke and I airmailed them a new one.
The repair was simple with my mechanic relative handling the tools. Total time about 25 minutes.
Previous repairs to the venerable machine with parts obtained freom Part Select and shipped to Germany: new drive motor and drum bearings.
The screen had holes in it and was leaking lint into exhaust pipe.
Just removed old tray and installed new tray.
I was completely surprised that in less than 24 hours the new part was at my door! This is the kind of service every company should strive to supply to the customer,and the delivery fee was regular 3-5 day delivery. A job well done !!!!
open the front of the dryer, open the back access panel, remove the old belt fragment, pull front cover away from bushing surface at the front of drum, drape new belt around the face of drum, match location visible as the track of old belt, reroute belt at the motor and install tensioner in the proper way, reattach front cover, install back panel, done.
