DCXH46EA0WW General Electric Dryer - Instructions

popped in one in

I removed the top lid, then removed the front panel, to expose top and bottom drum glides attached to panel, then using a carpenter shisel, and cutting knive scraped away the old worn out glides, wiped clean with acetone the area were the new glides were being cemented. all of this thanks to couple of customers that had the same issues on their dryer, and documented step by step their own way to have this done, I just followed thru their experiences.

Removed dryer top. Unscrewed the screw from each side inside the dryer the ones below the control panels. Don't unscrew those you will just have to put them back. Insert a flathead screw driver on the left side to loosen the front panel and slide it gently to the right. You can replace the drum glide without disconnecting any of the wires. Remove old drum glide and clean. Install new one and while the glue dries clean inside the dryer. Mine was very dirty!!!! Put everthing back and your ready to go. Don't forget to hook back the dryer vent. Thank you partselect my dryer is almost like new and is drying so much faster, no more noise and you have saved me lots of money.

Real simple, Unplug power cord from the wall outlet. Then open the top of the dryer by inserting a flat blade screwdriver under the front and pry up till the top snaps open. Lean the top to the back to keep it out of the way. Remove the 2 screws that held the front on and remove the wires for the door switch and the light. Remove the front by letting it lean out about 8 inches and lift it up out of the two bottom clips. Then just lay it any where it will be easy to work on. Clean where the new guide will go. Then just follow the instructions that came with the part. After the adhesive is fully dry just reverse the process and you are done.

Pulled the dryer front off to expose the problem. Thought it had a bearing of some type. Went to the PartSelect web site and watched the repair video. The Tech explained everything needed to make the repair. Ordered the parts kit and it arrived in three days by FedEx. Followed the directions. Simple. The video was excellent and made the repair a snap. Thanks.

popped lid pulled front scraped old seal off ,good kit ,worked great. you guys are great 2nd day delivery,on parts for fridge ice maker solenoids and dryer parts. you got me for a customer from now on. thank you. steve

* Clean off top of stackable dryer and remove top lid (pops off w/ screwdriver)
* Disconnect power supply and control wiring (right side under top lid)
* Remove left and right single screws securing front face of dryer
* Pop off dryer face w/ screwdriver
* Remove existing top glide from dryer face (peels off, use screwdriver or chisel/scraper to remove residue from felt and glue)
* Test fit new top glide
* Apply adhesive (included) to dryer face rim
* Clamp with 4 or so spring clamps and allow adhesive to set up (I waited about 30 minutes).
* Clean and inspect inside of dryer while the front face is off
* Clean dryer vent assembly (attached to dryer face)
* Reassemble and test easy rotation of the drum prior to use

1.) Unplug Dryer
2.) pop dryer lid by depressing 2 front clips with flat head screw dryer
3.) on back of dryer remove access cover and release belt tension
4.) remove front panel screws and then pop off front panel
5.) remove old gasket. Used XACTO knife, razor blades and acetone. Go slow and be careful.
6.) apply new high temp glue, let set up for a minute
7.) position the new felt gasket and clamp into place. I used C-Clamps and squeeze clamps.
8.) I let sit overnight.
9.) re-assemble and good to go.

NOTE: In retrospect I should have replaced both seals at the same time. The bottom seal is pretty worn but is still working out for now.

1)Unplugged unit from out let 2) Lifted top cover from base by prying up from the from the corners back is hinged 3) removed wires for door switch , removed a screw on the left and right from front. 4) pull front cover out from the top untill it clears drum then lift straight up off bottom clips. 5) scrape off old felt strip and guides 6) Sand untill all felt residue gone apply new glue to front cover wait a few minutes for glue to get tacky 7) clean out all the lint build up Checking from time to time that guide assemble is in place on front cover. 8) reinstall front cover when glue is dry.

Took off front door. Cleaned all of remaining felt left.
Put on glue and installed new part.

removed 2 screws, and released the clips holding the top of dryer. Lift top of dryer to expose drum. Remove old drum guide. Clean old adhesive off. Apply new adhesive, and attach new drum guide.

Works like new now

I ordered parts, recieved in 2 days. came with upper glide, glue and instructions. instructions were easy to read and follow. I used the wood chisel to remove old felt, cleaned well with some solvent, reap[plied glue, wait a few minutes , apply felt - reassemble dryer - viola- done. very satisfied customer

repaired as described in your instructional video.The video repair part of your website is just great.Seeing it done vs tring to understand someone else describe it makes it that much easier. I will use you for all future repairs.

Watched two videos...totally easy. Might have been able to stumble my way through it in 3 times the time. Watched the video and entire fix took about 45 minutes...awesome.

tilt up lid, remove front panel, replace guide, clean out dryer and reinstall.