Dryer was shutting off too early, before clothes could dry
Replaced High limit thermostat per video on the website. However, the flange of new thermostat is flat, while chassis it mounts on is round to conform to drum of dryer. So new thermostat was not flush with chassis. Dryer did not shut off early (that problem solved), but instead continued to dry clothes beyond time necessary. Note that old thermostat had one side of flange slightly bent and probably more flush with chassis, and better able to sense when hot temperatures were reached. I dismantled dryer again, slightly bent new flange, re-installed. Seems to work better now .
It was so simple. I removed the old ripped gasket by just pulling it. I followed the same direction with the new gasket by using a small screw driver to push in the tabs in each of the holes in the door. It works perfectly. They only fear I had was getting the part and the correct part, the model number of the dryer was on the door which made it easy.
Still waiting for your parts. over two weeks to get part which was a hinge for something, I don't know what, but not my dryer seal. You said you would refund shipping and wrong part and charge me for a new order. End result was I got charged extra shipping for your mistake. The part still is MIA and it has been 5 weeks since I originally ordered. Will never do business with you again.
Gas dryer only fired at the beginning of it's cycle
Be sure to segregate and label all screws. Remove back and front of control panel. Removed dryer top. Removed dryer front/door panel. Replaced slides. Due to discoloration it was hard to tell the white fr the green. Double checked partselect videos to be sure which was which. Propped up drum with the dowel to allow enough room to access the coils. One of the screws was frozen. Soaked in penetrating oil for 30 minutes. Then used a Philips headed socket to break it free. Used needle nose pliers to lift out old coils and to place new coils. Reversed process to reinstall all panels. Crossed fingers and tested. AOK.
First I watched the repair video on partselect.com and that really helped. It was really easy to replace the slides. I even ordered a new top bearing, old one was busted, and replaced it. Thank you for your help.
I removed the 2 screws and lock assemblies from both sides on the back. Then i removed 4 screws (two from each side) on the control panel and lifted that up as i tipped the cover forward to disconnect the wires from the door switch. I found the wiring diagram inside the control panel cover, which included a belt routing diagram (very helpful, being the belt was laying in the bottom. I then removed 3 torx srews holding the drum to the bearing, and removed the drum. Let the fun begin! i proceded to put the belt onto the motor pulley and around the tensioner. i needed some help from my wife to set the drum back in as i held the belt up around it. once the drum was back in, i found the beld had fallen away from the tensioner. I lifted the front of the drum up just enough to get both arms below it and move the tensioner back to slip the belt over it correctly. With the new belt on i started to put the screws back in the drum. This got very frustrating, as you have to correctly line up all the holes again, while holding the drum in the correct angle to start the screws. this was the hardest part, not physically, but wears on a person's nerves quickly! Once all the screws were in and tight, i took a deep sigh of relief before i tipped the front cover up just enought to get the wires hooked back up for the door. I turned the unit on to verify the repair before re-assembly. Yep! works again, for well under $20.00! Thanks PartSelect!
Took the top and front off. DO NOT TAKE DRUM OFF!! Lifted drum slightly and worked belt around drum. Replaced front and top. Took off rear panel at bottom near vent pipe. Put belt around motor and then tension pulley. Buttoned everything up and that was it!
Found excellent instructions and diagrams online by searching under the model number. Best of all was the service from PartSelect. Belt arrived 24 hours after ordering. It was the right part, it was easy to install, and the dryer is running beautifully.
Take out the two screws holding the top on with the door open remove top and remove two small screws in top front corners. I replaced the 4 slides and the drum bearing without the new felt, do not do this it continued to squeek after it ran the first few times when i got the new felt a week later i installed it in ten minuites and the noise is gone. I think it cost around sixty dollars and my dryer is back in action. Make sure that you clean all of the lint out of the inside of your dryer I had alot of build up near the chute for the lint trap.
handle broke on sunday( not the best day to order things). ordered it from this site and had it by tuesday. great service and best price i found on the web. tks
