Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Noticed oven was heating but upper element not coming on.
Removed two screws holding broiler element. Released two spring hangers on near the front of the element. Pulled element away from oven and pulled two wire connectors off. Simply reverse process to install new one. Wasn't the problem.
I removed the sensor from inside the oven with a 1/4” nut driver, pulled the sensor out slowly and then took the connection apart and found out that the connector was different, I cut the connector off of the oven side and then cut the connector off of the new sensor and wired it together. I am still trying to find the ceramic nuts. My oven is working for now. Very easy fix, just wish there were ceramic wire nuts with the new sensor
Your service was OUTSTANDING...Ordered one afternoon, and before lunch time the next day, the delivery man rang my door bell...Thanks a bunch for you excellent service.....
Oven light stayed on & smelled like electrical burning.
Wife was cooking our thanks giving turkey, when an oder of burning was noticed. I walked over to the oven and smelled the area of oven light, it was bad. I turned off and unpluged oven. Got a screw driver, unscrewed 4 screws then noticed the burned switch from under the oven top. removed 3 wires, covered w/ elec. tape, and pulled oven light switch out front. looked at part number and ordered online. We were able to cook our turkey and enjoyed our meal.
No power to burner until after dial setting 3 reached and would not reach highest setting.
1. Remove all four control knobs. 2. Unscrew all four plastic "nuts" found under each knob holding front panel to stove. 3. Lift front panel off. 4. Removed all Phillips screws holding metal shield to which control switches are fastened. 5. Lift entire assembly up. 6. Remove two screws holding bad switch to metal shield. 7. BEFORE REMOVING ANY WIRES LABEL EACH WIRE ACCORDING TO CODE EMBOSSED ON BACK OF BAD SWITCH. These will be H1, H2, L1, L2 and P. They are not in the same place on the new switch as they are on the old one. The reason for labeling is that in case you make a mistake you have this back-up to go by. Also to double check your finished job.If just one wire is connected to the wrong terminal a disaster will happen. 8. Remove each wire, one at a time from the old switch and connect it to the correct terminal on the new switch as indicated by the codes on the back of the new switch. When done double check to be certain the labels on each wire match the code for the connected terminal. 9. Slide furnished bushing onto the new switch. 10. Insert new switch through the back of the metal shield and attach with the supplied screws. The old screws were too short in my case so be certain to use the ones supplied with the new switch. 11. Re-attach the shield assembly to the stove. 12. Install the front panel back over the switch stems. 13. Secure the front panel with the four plastic nuts. 14. Install the control knobs. 15. Test the new switch.
Baking element got fried and turned into a pretzel with a crack in one loop
Cut power to your oven in your circuit breaker panel Take out racks and bottom pan from the oven Remove 2 screws in element bracket at back of oven Lift element gently, tilt upward and pull towards you out of insulation Get the tilted wire connectors clear of the back panel Remove two wires from from connectors gently with your fingers Take bad element out of oven Replace it with new element Replace everything else Piece of cake. 20 minutes max: remove old; plug and play.
Dual infinite range switch on left front burner of glass top range would stay on full high no matter what setting was selected on the burner knob.
Remove 4 knobs from front of stove.
Remove plastic nuts that are directly underneath oven knobs. Loosen with plyers and unscrew.
Remove front cover.
Remove 8 screws holding down electrical panel. Remove panel. Remove 2 screws holding switch into place. Transfers wires from old switch to new switch so you hook them up correctly. Then reinstall in reverse order. Job complete in 15 minutes.
Simply took oven out of wall, removed back plate, unplugged old sensor, went in the front and unscrewed old sensor, put in new sensor, went in back and plugged in new sensor, put on back plate, push oven in wall. Turn on power
1. Turn off power to the electric oven 2. Removed the two screws in the top side of the oven that hold it into the cabinet. 3. Made a support to set the oven on once you remove it from the wall. Or set it on the floor. You will need help this is not a one person job. 4. Used a Philips head screw drive removed the back of the oven panel. I did not have to remove the whole thing just took out half the screws and the electrical plug for the temperature sensor is right on the edge. 5. Unplugged sensor 6. Took out the two screw on the inside of the oven that holds the thermal sensor in place. Pulled it out the front. 7. Side the new thermal sensor in place replace the screws. 8. Pull the plug out and plug it back in. Check and push the insulation back in place where the thermal sensor. 9. Replace the back and replace the screws. 10. Slide oven back into the wall. 11. Replace the two screws that hold the oven in place in the frame. 12. Turn power back on Check the temperature
While removing burned out light bulb, the glass cover fell to the floor of the oven and broke!!
Husband very ill in bed. It's up to me!! Got a new bulb at HomeDepot and figured out how to get that wire 'thing' back in and the new glass cover installed. I DID IT!! WOW! My husband has always done these jobs around the house.......but now it's up to me.......and I'm not so dumb after all! I DID IT!! Now everyone who comes in the house.....I show them what I DID!! :-)
REMOVED DOOR OF RANGE. REMOVED THREE SCREWS ON ON BOTTOM OF DOOR . LAID NEW GLASS ON DOOR REINSTALLED THREE SCREWS. REPLACED HANDEL AND REINSTALLED DOOR ON RANGE
I usually try the cheapest part to replace when I come to a fork In the road but I wasn't home at the time and my other half called in the "expert". He said it was the clock timer and it would be $450 to replace it. She sent him away and I bought one online for $200 and put it in only to find out that it didn't solve the problem. Did some reading and found out that it could be the sensor. Put an ohm meter on it and found that to be the problem. Left the new clock timer in it anyway so now we're good for another 100,000 cookies or 1000 pizzas, which ever comes first