Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Washer Walking Across Floor,From Being Off Balance
1- Unplug unit 2-disconnect water hoses 3-put unit in open area so you can work on it. 4-Open top cover with screw driver 5-take off front cover with appropriate socket 6-lay unit on it back to get access to the drive belt (take off). And take off water hose with plyers. 7-With vise grips take off the six springs. 8-Take tub assy out,and lay it on the floor upside down. 9-Loosen the screws to take out the old snubber ring, note ( when lossening screws,keep your finger on the bottom of the screw ,so you can feel how far to back the screws out,just enough to have access to the snubber ring,to take out,and install new one. )Remember not to take screws out completely. The unit is under spring tension. 10-Put washer back together in reverse order,and problem solved!
Unbolt old pump with three bolt from top of pump inside the washer. Use needlenose pliers to remove intake and output hoses from old pump. Remove belt from pulley under washer. Reverse procedure to install. I was worried because there were two pumps listed for this model number, one being $95 and the other being $40. I bought the cheaper one and prayed. It worked just fine. Fixed a $500 washer that was on it's way to the dump and made $100 in the process!
Had wife balance washer on front edge while I accessed working parts from bottom of washer. Removed drive belt and turned agitator pulley, transmission pulley and drain pump pulley by hand. Drain pulley hard to turn and shaft had play in it. Ordered new drain pump and replaced upon receipt. Very few fasteners to remove and replace pump assembly. Drive belt was easy to remove and replace. Recommend also replacing drive belt on a washer this old.
Washer making loud noise when water pump operating, still worked but made very loud noise
I ordered the replacement pump assembly (water pump)for my Atlantis model maytag washer, removed the old one, installed the new one and works like a charm. The only difficulty I had was trying to figure out how to remove the cover on the front of the washer, to remove the clips, it slid side to side instead of popping out, found the instructions on-line, NO instructions came with the pump but if you have any common sense when it comes to repairs it was easy to remove and install the new part.
I found on-line that replacing the snubber ring may fix the problem and ordered the part. With the instructions also downloaded I started taking the washer apart. Without the instructions the task would have been more difficult and possibly disastrous as I might have taken the bolts out that tighten down the snubber ring. All went well with a little patience. The washer works good.
Laid washer on its side, released five of the six tub springs, then removed the dive belt and the main pulley. With some effort removing the old snubber ring, placed the new snubber in place. After fighting with the large spring under the pulley I was able to replaced the six screws with the help of an assistant. Replaced the pulley, belt and the five springs. Closed the unit up and placed all the hoses back in place. I was amazed at how smooth the washer functioned with no vibration at all! Thank You.
Made an awful sqealing noise and did not spin the water out all the way
Leaned the washer back and propped it up and changed the belt. This is the first time ever repairing an appliance. I feel very good about myself as I am 49 yrs old and did not have to call a repairman for this.
I pulled the washer away from the wall so that I could lean it back at an angle. I removed the old belt and put the new one on. I started with the smaller pulley first and put the belt into the groove. Next I went to the next larger pulley and did the same thing. Then I went to the largest pulley and started to put the belt into the groove and started turning the pulley by hand. The belt went right on.
Troubleshoot problem, removed front, removed drive belt, removed pump with pulley. Note, new pump did not have black plate, installed worked great.Thanks
I had to raise the top of the washer and take off the front pannel. It was not too hard to replace the pump except that it was in the back corner and it was hard to reach the bolts to remove and install the new pump.
open top,remove back panel.then laid on the side and removed belt.remove hose from tub to pump.removed small hose for fill level.Hard part was to remove springs from tub.Then pull tub and transmission out of housing.Remove pulley from shaft.Lossen screws around snubber ring but do not remove them.Remove old snubber ring.clean surfaces with alcohol.install new snubber ring and assemble in reverse order.
loud sqeaking noise, burnt rubber smell, motor siezing up
Unplugged electrical plug. Disconnected water and drain hoses. Turned washer on front side. Removed old belt from bottom of washer. Removed pump access panel. Removed old pump. Installed new pump. Torqued pump mounting screws 1/4 turn with socket wrench. Installed new belt. Put on pump access panel. Hand tested motion of belt and pulleys for smooth travel. Put drain hose on. Turned washer in the upright position. Reconnected water hoses. Washer works like new.
