Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The Baking element in the bottom of the stove apparently shorted out and partially melted
First I turned off the circuit breaker on the house electricity panel. I removed the two screws that held the element in place in the oven. There were two wires connected to the element by spade plugs that were free floating in a fiberglass pad. I reconnected the spade plugs and put the element back in place and put back in the two screws. This procedure had I known what I was doing could have been done with the stove in place and would take no more than 5 to 10 minutes. Having no experience at this, I had pulled the stove out into the room and also removed the back cover which turned out to be unnecessary. I put everything back in place and held my breath and turned on the circuit breaker. Voila! It worked!
Getting F 1 and 2 error codes and the oven turned itself off.
Really easy but in this model there are 2 versions of the sensor, male and female. The website didn't have any place to see that. So the first sensor that came was male but we needed the other. After calling they sent me a return form and sent the new part (which was actually much cheaper) overnight and it went in very quickly. Would check this out again when anything went wrong. they are great folks to work with.
The oven light has been broken forever-I turned on the oven and the element started flaming.
My husband replaced the bake element in moments. We couldn't get the broken light out of the socket because we couldn't locate our needle nose pliers. After a few days I finally got tired waiting and found a small pair of pliers in the house and got the remains of the bulb out and screwed it in, and plugged it in and we're in business! Never wait for a man to do what you can do yourself! I was so pleased that ordering the parts on-line was so easy and I didn't have an expensive repair bill to pay!
Turned off power to unit. Tilted up Glass top and removed two screws holding rear hinges to range. Then I unplugged wire harness from lower range and placed the Glass top facing down on counter top with towel for cushion. Removed 1 screw holding center of burner to support frame, two alignment screws on perimeter, and two screws holding support frame to glass top. This allowed me to slide out the old element with all wiring connections intact. Placed the new assembly in same location under support frame, noting numbered positions of two alignment screws from old unit. This is necessary to properly align heater to surface glass. Replaced all screws connecting burner to frame. Then I removed each wire one-by-one from old unit, reconnecting to same location on new unit.
Replaced top in reverse order from removal. Powered on the circuit breaker and verified proper operation of dual unit with large/small selecttor switch. Total time to repair about 30 minutes.
un-screwed 2 scrws and pulled out the old one and pulled off the 2 wires put the new one on the floor of the oven and hooked-up the 2 wires and pushed it in the back wall and replaced the 2 screws! done maybe 5 minutes
I removed only 3 screws that allowed me to lift the glass top on the stove. I removed the burner and I could see where it short circuited. I ordered the new burner element. After it arrived I replaced it by moving the wires from the old element to the new element, and put it back together. I am sure that I saved at least $200 in "labor".
first I unplugged the stove,took the screws out of the pan that holds the element to the stove, then unplugged the element.then I plugged in the new element, then screwed the screws into the pan that holds the element into the stove. it was very easy.
Oven never came up to correct temp. Broiler did, so it had to be the bake element.
Turned off the power! Unscrewed the element (2 screws) pullled the wires out. Put the new part right in. Easy! Thank you-only a week before Thanksgiving, what a life saver! Also, order on Monday AM and was delivered by mid-day on Wednesday!
Pulled stove out and unplugged it (energized wire at burner even with burner turned off) Removed screws to lift cook top Removed burner support brace Removed three screws to remove burner Removed connections from old burner, installed on new burner Replaced screws in burner to brace Replaced burner brace Lowered cook top and installed screws Plugged in stove and pushed it into space
Regarding my right side oven door hinge replacement, P/N PS2172201
After reading that other people had trouble threading the screws into the new hinge, I looked at the drilled mounting holes in the new hinge. Neither hole was threaded. The smaller hole used a self tapping sheet metal screw which works fine. The larger hole gets a machine screw and will not self tap. Since the instructions say put the screw in "once" to tap the holes before installing the hinge, I tried this. It doesn't work, regardless of what the instructions say. The larger hole should come from the manufacture threaded. I do have a tap and die set so I tapped the hole myself. After that, the installation is a 5 min. ordeal.
Take the two screws, one on each side, out that hold the oven door on the hinges. The door will then pull straight off the hinges. Take the storage drawer below the oven out. Unscrew the top and bottom hinge screws and pull the old hinge out from inside at the bottom. Put the new "threaded" hinge into position and hold from the bottom, inside. Screw in the two screws, large one on the top end, and put the door back on. You can open both hinges about 30 degrees to allow the door to slide back on the hinges easily. Put the last two screws in that hold the door to the hinges and you are done.
Really very easy and saved several hundred dollars in repair bills. I might add that my hinge arrived on time 3 or 4 days after the order was placed.
My bottom oven didn't work, and I had called a service to come out and fix it. It was a $60 charge just to come out. My friend owns an apartment complex, and she told me it was two screws and a pull to remove the element and replace. I took the element out, ordered it for $38, had it the next day and repaired my oven in a matter of minutes. It was so easy and inexepensive. I feel like I can do anything!
The high ekement on a dual burner range top burned out
Turned off circuit breaker and unplugged. Opened oven door and removed 3 screws holding the range top to the range. Lifted top and proped open with a wooden block. Removed all 5 wires to the element and drew a diagram of where they came from noting the color code. Removed two screws holding the bar that supported the element and dropped slightly while removing the two standoff screws holding the element in place. slide the element out. The problem was that the element received from partselect.com did not physically match the terminals on the original. this required me drill out a brad on the terminal block cover to see how the terminal block was wired. I discovered that the different color wires on the old element went to physically different terminals on the new one. This was even though I had returned the first element received, got a new part no from matag and reordered. there are tiny markings on the terminal block that helped show the way. Be sure to find them and rewire according to these markings. 1a 2a 1b 2b as the terminal locations may be different. I am happy with the partselect,com and their attention to trying to get me the exact replacement. Also happy with their return policy.
Removed the door and old hinges and reinstalled the new hinges and added some screws to better support the door ( it was bending a little at the middle and the door would not shut all the way. Now it works fine.