Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Oven would not maintain temperature
First I removed the oven racks, then the bottom cover over the burner. I then unscrewed the two screws holding the igniter on to the bracket on the burner tube. I then removed the storage drawer and loosened the two screws holding the metal shield in place. I then unclipped the electrical connection to the ignitor and pushed it up past the insulation. I then went back into the oven and pulled the wires and connector through. The old igniter was out!
Installation of the new one was just as easy. Screwed the new igniter onto the backet, stuck the electrical connector through the hole in the back of the burner tube, and connected it. I then replaced the shield and the storage drawer, replaced the bottom pan over the burner tube and the racks. The stove works perfectly and my wife is happy. The job couldn't be easier.
Found serial # as advised on web site. Found parts listing & ordered part. Got it in less than a week . Unfastened two screws on top of door. Inserted glass. Applied a little mastic to prevent it from coming out again. Done & done. Do I get a prize ?
My Husband did the repair in less than an hour. He followed the way it was put together removed it the same way and replaced the whole unit very easily.
the oven door would not shut all the way, so heat was leaking
The part fit perfectly.Ther repair was logic. The door was of course heavy . I needed an extra hand. I would have appreciated of instructions were included with the part. Also a web link on how to do it would alos have helped greatly
after i recieved the parts with the glass still laying on the foam pads it was packed in i put some soap on the bottom so the new bracket would slide on easier. i centered the bottom bracket on the bottom of glass and pushed in place. i then picked up glass and slid it up in place on oven door attached the screws on bottom done
Removed the drawer from under the stove then unscrewed the access panel in the back (two phillips head screws). Rather than take it off altogether I just swung it to one side.
The ignitor electrical connector required two hands to disconnect and it was a bit of a reach but came apart easily enough once I got hold of it.
Removed the racks and bottom from the oven. the bottom is held in by two pins in the back that you just slide toward the front then lift it out. I did not bother to remove the oven door, but some people might.
Then removed the two hex head screws holding the ignitor on and pulled the connector out of the hole leading to the bottom.
Installation is the reverse of removal The electrical connector was reluctant to back down the hole, but went with a little wiggling and pulling from underneath. Once you get it back down there the connector is keyed, so you can't get it wrong.
Piece of cake, really.
Total repair time: about 30 minutes, including the mandatory halfway beer break.
A friend helped me to fix it. First I removed the door from the oven itself. Next, we unscrewed the four screws from the glass holder at the bottom of the door and removed it. Next, we straightened out the glass holder, as it was slightly bent up from the front glass shattering. Next, we slid the glass into the door. Finally, we reinstalled the door to the oven. Voila! It was like brand new again.
one screw holds the cover to the connector. one screw for the burner tube to the oven frame. two screws hold the ignitor bracket/assembly to the burner tube. that's it. take four screws off and disconnect. connect and put four screws back on.
Removed oven door by opening slightly and lifting straight up. Pulled out racks and removed bottom of oven. Unscrewed wingnut and removed burner shield. Removed 2 screws that hold igniter and unplugged the connection. Reverse the procedure to put it all back together. Be patient, it takes a few moments for it to begin heating when you first turn it on. So easy a woman can do it ! I know,(I am one).
I received my glass panel realy quick from Part Select. It was an eansy job to install the new pane. It took less than an hour. Thanks for Your prompt service.
Nothing mechanical was required! But the service was phenomenal. These are just a drop in part. I was thrilled that you had them, received them in one day without overnight charges, And the cost was very reasonable.
I removed the oven racks, the bottom of the stove and a v-shaped cover that was over the heating element. The old gas ignitor screwed off easily after I put W-D 40 on the nuts. I un ooked the old gas igniter and replaced it with the new one. The oven lit immediately after I replaced everything. I am very proud of my self, I feel like a femal Bob Villa. I almost bought a new range. Boy am I happy!