Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
6" surface heating coil remained warm when "off"
Removed the large lower back panel of range (6-8 phillips screws) which holds upper control back panel in place. Removed upper control back panel (2 screws), exposing infinite switch electrical connections. At front face of control panel, removed (pulled off) control knob, exposing 2 phillips screws holding switch in place. (NOTE: A sleeve is on the switch arm or maybe remains inside the control knob). Look for this sleeve. Without it, the knob will NOT seize the switch rotary arm. Removed each wire connection individually, one at a time, installing it in the proper position on the new switch. Reverse all procedures to put things back together. A very simple, straight-forward operation.
It was really easy. It took about 5 minutes to remove the screws holding the back in place. Another couple of minutes to remove the switch, and a few more minutes to change the wires over one at a time. Then 5 more minutes to put it all back together again, and plug it back in, and it just worked. Really simple.
Oven not heating pass 125, heating element not working
First I removed the screw behind the stove that hides the electrical wires. Pull off the two wires connecting the bake element with pliers. Unscrew the two screws holding down the floor pan which covers the baking element and pull out the floor pan. Here you will see the baking element, it is attached with a few screws. Remove the baking element and attach the new the same way. We could not believe how easy this repair was to do. Not to mention all the money we saved on a repair man. Thank you partselect.com, I'm glad I researched this on the net.
I slide the range out and unplugged it from the outlet. I removed the back of the oven ( 8 screws ) using a cordless drill and phillips bit then with a phillips screwdriver I removed the oven sensor (2 screws) then I installed the new sensor , reinstalled the oven back , plugged the range in , slide it back into place and that was it. This repair took about 10 mins and the oven works perfectly. Thanks !
Turn off breaker in electric panel fore stove. Put screw driver into slots in front of glass top surface. Pry top up carefully until top pops up.Remove burner dial, remove two philips head screws holding switch. Lift top carefully and prop up.With new switch close remove wires from old switch one at a time and place on new switch. Place new switch back in place, securing with philips screws. Remove prop and carefully press top down until it snappes into place.Replace dial, turn breaker back on and try burner.
Burnner would go to high setting no matter what the setting was.
Shut off power at breaker box , pull stove away from wall , remove Phillips screws from back of range pull knob off of switch . Look to see how switch is oriented remove 2 screws that hold switch in . Remove one set of wires at a time and place on new switch in same location . Put back together in reverse order .
Removed the approximatly 10 screws that hold on both the upper and lower pieces of sheet metal that cover the back of the oven. Removed the screw holding in the temp sensor. Unplugged and removed the old sensor. Plugged in and installed the new sensor (using one of the included adapter wires supplied with the sensor). Put the 2 pieces of sheet metal back on and plugged in the oven.
the old gaskt was not linge dup well, the door was not closing well
pulled the old gasket, the new one fitted perfectly. No effort at all. An instruction sheet would be a bonus. I wish you put instruction sheet in all parts OR a web link for video instructions. a web link would be great
Remove sides and face of oven door by sliding down from under the oven handle trim.
Remove screws on 2nd light of glass and set aside.
Now you are at the inner door panes. their should be two in an insulated type unit.
Remove the remaining screws from the handle pracket and the permiter frame for the glass/insulation. Remove permiter frame and set aside.
Pull out inner door glass frame. get a pair of pliers and bend tab on frame up so you can pull the frame sightly apart, replace the glass, secure frame tightly around glass slide tab back into reciever slot and bend down ( you may need another person to assist in keeping both lights in the frame while trying to ben tab back in to place)
reassemble door as it came apart carefull not to over tighten the screws, they strip easy.
My wife dropped a cast iron dish on the door while it was open, bent the hinges, so it would not close properly.
It was really easy, just lift the door off from the range, I set it down on the box that the hinges came in, took the six screws out to release the front fascia of the door from the back, hinges are right there, un-screw and install the new hinges, put everything back together in reverse and lift the door back on to the range, less than 10 minutes!
Indicator Lens melted and fell back into the control panel
I took the back panel off, removed the old lens, installed the new lens. How easy to order from home, receive the part, do the repair and pay less than it costs to simply drive to the parts house. Cool....
Turn off breaker to oven and verify no power. Remove the two screws holding metal panel covering baking element on the floor of the oven (near back of inside of oven) Remove two screws holding element mount to floor of oven (near front of inside of oven). Remove single screw holding element to back wall of oven. Pull element toward front of oven, carefully holding wires so they do not disconnect from element and slip inside the ovenback wall. When you can reach the wire connections, hold each one with a pair of pliers and disconnect from element ends. Connect new element ends into wire connections. Be sure to insert all the way into both connectors. Carefully, push the wires back into the rear of the oven, trying not to scrape the wires on the sheet metal. When fully inserted, reinstall single screw to secure element to back wall. Re-install two screws to element mounting at the front of the oven floor. Re-install two screws to secure element cover plate to the floor of the oven. Turn on breaker for oven and verify oven has power. Turn on oven to bake at 400 degrees. Wait for oven to come up to temp and maintain for 10-15 min (you may smell some burning smells as the element heats up the first time). Enjoy...
First I removed the two wires from the back of the stove. I then removed the two screws that were holding the element in place. Installed the new one without problems