Replaced the heating element assembly. Problem was still there. Checked the electrical schematic to try to resolve. Everything checked out except the contacts on the motor M-1 to M-2 had no continuity. Removed the switch from the motor and exercised it. Works fine now.
I first looked at your directions then felt I could do the repair. So I ordered the part. The video was extremely helpful and allowed me to follow each step in the process. Last time I paid $270 for the exact repair. This time I costs me under $30. Plus I was able to clean out the entire inside of the dryer. The sitr instructions were very helpful and on target for any level of experience. I fixed my own dryer and saved a ton on it! Thank You, Randy In Colorado
May not have to take out the whole drum to replace the limiter!
After lifting the dryer top and finding the location of the thermal limiter on the back of the dryer, where it is difficult to get at, I carefully cut through the dryer cabinet with the multimaster on three sides to form a 'flap' upon which the limiter was mounted. By prying this flap open from the back, the two wires and two screws are easily accessible to replace the limiter, without having to remove the whole drum. Afterwards, I just bent the flap back into place and taped the seams. If it ever blows again, the fix will take all of about two minutes.
I basically followed the video instructions on your website. Pretty simple but ran into an issue pre-threading the 3 self taping screws into the spindle bearing. The screws provided were blunt on the end and did not tap easily at all. I used the existing screws that were much more "sharp" and worked much better. Also, the new screws were Philips drive and due to the amount of torque trying to self tap nearly stripped them out. The old sharper screws were square drive which had a better bite. So basically, I used the old screws to self tap and then used the new screws for the final installation. It took a long time to clean all the lint out from the inside of the dryer. The motor was completely embedded with lint and animal hair. You may want to suggest that a good cleaning may be needed so bring a shop vac...and also something to carefully pick the lint balls out from around the motor armature and bearing area. Overall the video instructions were really a big help!
Had a squelch/squeak coming from the rear of the unit
I looked up a YouTube video on my specific model. Found one that said “basic disassembly”. I watched that and had it apart and back together in no time. Very easy to take apart and put new parts back in it. Re-assembled and since the repair no squeaking.
Watched on-line video, then applied those steps. 1. Pop the front of the deck loose using putty knife to depress clips; 2. Disconnect wires from light and door switch; (Before I disconnected wires from door switch and light, I made wiring sketches to make sure I reconnected in original manner.) 3. Remove lint filter mount screws and mount from bottom of door opening; 4. Cut drum belt with wire-cutters and removed it; 5. Remove drum support clip from top center of front panel; 6. Remove (1) screw from each side of dryer body that hold front to sidewalls, removed front panel; 7. Remove drum by lifting the rear out of the bearing, then moving it forward through the machine front; [While I had the dryer disassembled, I thoroughly cleaned it of lint, dirt & metal filings. The metal filings were from the worn ball hitch and drum support bearing cup. I spent as much time cleaning it out as I did working on it.] 8. Stand drum on gallon paint bucket while removing ball hitch (Use a #2 drywall phillips apex to obtain sufficient seating & torque to remove and reinstall ball hitch screws at rear of drum.); 9. Have a second person hold the new ball hitch in position while starting screws, if necessary; 10. Use nut driver w/5/16" socket to remove bearing retainer & ground ball clip; 11. Install new bearing into retainer clip, insert attachment screws through the holes in both, stick grounding ball in depression on back of bearing as screws are fed through back panel; 12. Hold ground ball clip in place to start one screw, then the other & tighten with nut driver; 13. Start drum belt on motor shaft and position against tensioner pulley; 14. Feed drum through front of machine and loop belt over rear of drum; 15. Slide belt forward on drum as drum moves to rear to keep it aligned with position of tension pulley; 16. Lift rear of drum to place ball hitch on top of bearing, then press down to seat it into bearing; 17. Turn drum to ensure belt alignment, then re-accomplish steps 6 thru 1.
Remove top lid by pushing tab on either side with a putty knife. Disconnect the 2 wire carriages on right. Remove one phillips head screw on each side that holds front panel to dryer body. Remove front panel by using flat head screwdriver to pry panel from body. Remove thermostat located on bottom right attached to front of motor on a plastic body by removing two phillips head screws. Disconnect wires and place on new part.