Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Broken burner switch. Would not shut off.
Turn off breaker to the oven. Removed four knows by pulling them up and out. Using either a large flat blade screwdriver or adjustable wrench (depending upon stove top model) remove threaded style holders at each burner switch control to remove the glass clock control top panel. Remove glass panel and note ldgasket position. Place glass panel on top of stove top on a cloth towel to prevent scratches. Remove 8 screws and remove/lift up burner control assembly. Invert and place on its side to gain access to broken contol switch. Took a picture of wiring and close up off switch to help remember where each wire plugs into switch. Remove 2 Phillips screws from the old switch and remove from panel. Using a flat blade screwdriver gently remove one wire at a time and using knob to orientate the off position of the new switch. Remove each wire one at a time and install on the new switch. Compare numbers on both the old and new switch to assist where each wire goes. The numbers are beside each terminal and using a flashlight and magnifying glass will help making the job easier. DO NOT mix the wires up. Use the 2 longer screws and threaded bracket supplied fasten the new switch to the glass panel. Reinstall the glass panel using the screws removed and thread on clips at each switch and tighten using a large flat blade screwdriver. Be sure to route the wiring to not pinch the wires and install the gasket along the front edge which fills the gap along the burner top and side for a tight seal keeping water and food particles out. The infinite control switch has letters such as H1, H2 etc as the switch fits several models with different wiring diagrams and colours so it's impt to note this when transferring the old wires to the new switch. Also the gasket along the top glass edge ensure to note exactly how it is placed to reinstall to be exact when you reassemble. Replace the 4 control knobs by pushing them on after aligning to fit as they were removed. New switch should be positioned the same as the others with off at the top and a notable click. Be sure to note this when transferring wires from the old to new switch. Turn breaker on. Note: If you have minimal skills this should be left to someone who is an electrician or has repair experience in this field.
unscrew the sensor inside the oven; took off the back of range to access harness of sensor; the replacement part harness did not match up to the original, so we stripped the clip from the end of the part and also the end of the harness in should clip into. after joining the wires together with ceramic wire nuts we tested the oven to make sure all worked AND IT DID!
Dual burner would only work on high and only the large burner worked
Replaced the dual infinite switch behind the panel. The wires were easily matched, even though the switch looked a little different. Works perfectly now.
The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.
Oven wires arced and caused the terminal block to melt and become detached from the back of the range
Removed the wires that I could, then terminal block. Installing the new terminal block was very easy; however the wires that arced were fused to the terminal bock screws and needed to be cut and new connectors had to be put on the wires to allow them to be reattached to the block safely. Once all was replaced and reinstalled the oven has worked great. The length of the repair was increased because of the melted parts and having to run to the store to get the new wire connectors big enough to fit on the wires. If we were simply replacing the block and had not encountered the melted ends, it would have been a very quick and easy repair.
my original part arrived and it did not fit. When I called to explain the problem I was told it was the wrong part. The big problem is... Frigidaire calls the receptacle a terminal block kit as well as a terminal block kit which is a totally different part. I tried to explain that to several different folks I spoke to at your company as well as Frigidaire but I'm not sure if I got that point across. Take a look at part # 530 393 5058 and part # 530 440 9888 and you will see that they both mention terminal block kit. Hopefully the part I am getting from Frigidaire is an OEM part and will fit.
1. Loosened 2 sensor mounting screws and removed them. 2. Tripped range circuit breaker to off. 3. Pulled out the range but left gas connected. 4. Loosened the 4 screws on RH side of the top back panel and carefully pried that side of the panel open. 5. Using fingers, threaded the sensor's wiring harness through insulation and into the oven. 6. Unplugged old probe. 7. plugged in new probe. 8. tugged wiring harness back through insulation behind the oven. 9. Using 2 screws removed in 1 above, mounted new sensor. 10. Repositioned top back panel and fastened it in place. 11. Shoved range back in. 12. Tripped range circuit breaker to on. 13. Reset clock. 14. Set oven to 450 for test tun. 15.
Watching the video showed an easy, unscrew and screw back on process while connecting the wires back. It was really that simple. Once it was complete (not even 10mins), plugged it back in, and its been working great since.
Really a no brainer, but I do have to say that PartSelect customer service is excellent. My part was located and on it's way within a day and arrived a couple of days later.
