Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Frame was broken
Removed 2 screws on the bottom, and 3 on the side of the handle. Pull out at the handle side to release the back of the frame. Removed glass and trim from old frame. Re-installed glass and plastic trim on table. Remove old handle and install on the new frame. There are 2 screws for the handle. Then hook the back of the frame on the left side. Push the handle side of the frame in. Re-install the 5 screws then your done.
This is not easy to do. I done it before to replace a broken window and it was a real bitch. I considered buying a new door rather then do it again.All I wanted to do was tighten two screws that hold the handle. I used the advice found on your web site from a person who did it using quarters and putty knifes to remove the choke and the door insert. Sounded silly but it works like a charm. I advise anyone who needs to do this repair to use that info on your web site. It will save lots of frustration. Be sure to have plenty of quarters and a few pennies.
I turned off the power to the oven at the breaker. I then removed the side trim pieces by removing the screws located behind the lower oven door. I removed the plastic trim pieces above and below the microwave oven and removed the control panel and slid it into the opening above the microwave. I located the two screws securing the microwave into the frame and began sliding it out. I had to disconnect a small wiring harness and two wires from the microwave that were attached inside the opening above the microwave. The microwave section was the easily slid out, turned on it's side where the turntable motor was accessed by removing the access panel. I pulled the old motor, checked resistance and it matched the new motor. I then checked the old motor by applying 120V to it and it ran FINE! I thought I had the wrong part, but decided to install the new motor anyway. I did, secured the access panel and replaced the microwave in the frame. I reconnected the wires and secured the control panel and tested the microwave...and the turntable works!
the burn thru was probably because stirrer motor was not turning, Unplug the microwave .freed the motor up bu manually turning. temporary fix. The cover is held up with small push pin clips. Just pry the cover off with a screw driver or other flat tool. Scrape offf the old silicone. There are two covers in the Kit. you just need 1. Remove the old clips for the roof of the microwave, put a bead of silicone on the new cover where the old was and secure the new cover with the push pins into the clips .
A phillips head screwdriver and a bottle of windex to clean the parts were all that it took to repair a very expensive microwave whose door and vent had cracked due to age. Half of the time in the job was spent cleaning the old parts before reassembly. There were five screws total. This isn't rocket surgery. :-)
The display kept asking me to close the door, even though the door was closed. The interior light stayed on.
I used a Google search to show how to access the area behind the front panel. There was a folded paper copy with a schematic and wiring diagram in that space.Then I used a multi-meter to determine which of the THREE micro-switches was causing the problem. I called your help line and ordered a replacement switch. The switch was delayed in transit so your agent credited me with the cost of shipping.
When the part arrived, it had three terminals instead of two as shown in the on-line picture but that did not cause any difficulty in using it. It took about 20 minutes to remove and replace the old switch.
All seems to be working well now.
Finding which of the THREE switches was the problem was the most difficult part of the repair. All three "clicked" but the defective one did not click as easily. It needed to be depressed more than the door latch can would provide. Old age?
Remove 6 screws, remove glass and black molding. Then I placed those items in the new frame. Placed the frame on the Hinges and replaced the screws. It was that easy.
Overall a very easy fit, the key for me was being gentle with the glass if your door has an extreme crack (as mine did). If it does, the glass can easily fall out of the frame. The plastic clips that hold the glass to the frame are also quite fragile, so just gently work the glass into the clips without forcing it.
Took me about 20 minutes.
1) Remove 3 screws from side of door 2) Remove 2 screws from bottom of door 3) Carefully slide outer frame of of door.
If crack is extreme (as mine was), be careful that the glass does not completely fall out when removing frame
4) I used a putty knife to carefully pry up the top part of the frame as it has clips that fit into slots on the door. 4)Once frame is removed use screwdriver to remove door handle 5) Remove glass from frame and replace with new one. Use the putty knife to gently push the clips onto to it as the plastic clips that hold the glass look easily breakable 6) Re-attach door handle 7) Slide new frame back onto door, push top clips down into door top and replace all screws
Take off top facing over microwave using screwdriver also protection plate for diode and capaitor. Disconnect diode from frame, bracket to capacitor then remove, disconnect wires leaving diode on capacitor for right connection, replace, rewire done.