Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The heating elments were getting old kicking breaker
took out the old heating elments and cleaned the bottom & top of oven with out the elments in, which made it alot easier then put new ones in. They were very easy to do, just make sure you watch how you took old ones out and don't loose the screws cause you use them to put new ones in.
The broiler unit had disintegrated at both connections. I removed the two screws in the top of the oven holder the unit, pulled out the unit, measured and ordered a replacement.
To replace the element, I pulled out the stove, removed the rear panel, located the connections for the broiler unit, remove parts of the old unit. I then attached the new unit to the top of the oven with the two screws, went around back and pushed in the two connections, replaced the back cover and replace the stove. It took about 30 minutes because I cleaned everything and sprayed bug spay (another plus for doing the repair myself).
1. Turn off oven. 2. Switch off circuit braker to oven. 3. Remove two screws holding element. 4. Pull element out to expose connectors. 5. Disconnect connectors and remove element. 6. Reverse procedure for installation.
grandson removed the two screws holding in the burned out unit and removed the two wires, installed them into the new unit and put the prongs into place. very easy and certainly very economic. delivery was quick and postage was reasonable. Thank you.
I had previously partially removed the element and tested with multi-meter to determine that it was not working (open circuit). Repair procedure follows:
Turned off Power Removed 2 retaining screws Pulled element out part way Removed 2 spade connectors supplying power Replaced element w/new element Reversed procedure Tested Oven; worked fine.
This microwave is the upper unit in combination with an oven. Microwave portion is Model RM288PXS. Cut power at breaker box. Remove metal frame around 2 sides and top, (5 screws). Remove 4 screws on bottom, whicn anchors the unit to the frame.Remove contol panel (2 screws at top) and swing down. Pull out female electrical socket at bottom right back in conrol unit space. Now pull out microwave from frame about 6-8 inches. This provides access to pulleys on the motor and wave disperser. Put on belt. Reverse the above procedure to finalize the repair. This is the 3rd time I have had to replace this belt. They last about 6-7 years. Without the wave disperser , the microwave does not provide even heat.
Turned off power at circuit breaker. Removed 4 phillips screws from area over oven door. Pulled control panel out and twisted to clear top rail. Pulled two wires off of old switch.Pulled old switch through panel. Inserted new switch. Attached the two wires to new switch. Replaced panel and inserted four screws. Turned on power - it works!
The new handle, braces and screws arrived as quoted. My son-in-law installed the new one without much trouble. The handle is black and matches the black front of my stove. The older handle was sort of a wood-brown. Thus I like the new one better. Thank you for good service and prompt attention to the problem. Linda Archibald Hanson, MA
When the oven was on we noticed the bake element had a 1 inch section that was bright red. Upon closer inspection, after the oven was off and the element cool, corrosion like damage was apparent where the element had been bright red.
Naturally the oven turned was off but for added safety I also set the breaker protecting the oven to the off position. Where the element attaches to the oven there is a small plate with two screws holding the element in position. Remove these two screws and then gently pull the element out 2-3 inches, which will expose the electrical connection. Using needle nose pliers gently pull on one of the wires to remove it from the element. Now remove the other and discard the old element. Simply plug the new element into those wires and screw the plate back into the oven. Now turn the breaker back on and you're done. Super easy!
items in the oven were not baking properly. We discovered the bake elemnent wasn't working and looked defective in one part.
I removed the back panel, unplugged the wires, removed the 2 screws, replaced the element, plugged the wires back in and put the back panel back on. Now that I'm thinking about it, I guess I didn't even need to remove the back panel to replace the element.
My husband is an over-the-road driver, so I have to do all of the repairs myself. I went to the breaker box and turned off the power to the range. Then I removed 2 screws, pulled the element out about 3", and disconnected the wires. I then connected the wires to the new element, pushed it back in place, and replaced the screws. We had Parmesan Chicken for dinner and my children were thrilled!
I removed two screws, pulled it out a few inched and unpluged two wires. I then plugged the two wires into the new element slowly slid the wires and element back into place and put the two screws back in... and it worked perfectly. I did it all in less than five mins. And I am a 53 year old woman.No man was required.
