Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dishwasher basin would fill and then dishwater would shut off. The water was not pumping into the cleaning showers.
To empty the water in the dishwater basin, I pushed the cancel button and closed the door. I then turned the electrical breaker to the off position that supplies electricity to the dishwasher. I confirmed the power was off by attempting to start the dishwaser. I removed the metal plate between the dishwater door and the floor by removing the two screws. I removed the two screws that connect the top of the dishwasher to the underside of the countertop. I shut the water valve that supplies hot water to the dishwasher (mine was located under the sink). I disconnected the drain hose (plastic) by using pliers to loosen the clamp the holds the hose on the outlet of the drain pump (drain pump is much smaller than the pump that needed replacement). A towell is handy to soak up the water that comes out the hoses. I loosened the nut on the water supply hose (this was difficult because of lack of room)using a wrench and pliers. I opened the door on the metal box that houses the wire nuts for the electrical connection to dishwater, and I removed the wire nuts and the screw for the ground wire. Once the white, black, and gound wires were disconnected, I could pull the dishwater out. I also had to pull the drain hose out from the clips on the side of the washer to pull the dishwasher out into the middle of the kitchen floor. I flipped the dishwasher on its back. I removed the single bolt that held the broken pump motor to the dishwasher, and then the motor twisted counterclockwise and I pulled it out. The pump shaft would not turn freely with my pliers, so I knew the motor was broken. I removed the pump end (impeller) from the dishwasher by tapping it with my screwdriver. The impeller end came out along with a metal screen. The metal screen was 50% plugged, so I cleaned it and put it back in place. I wet the gasket on the new pump motor and slid it back in place while rotating clockwise and locking it in place with the tabs. I replaced the bolt that holds the motor in place and reversed the repair procedure to re-install the dishwasher. Be sure to run the dishwasher and look for any leaks. The last step is to replace the metal plate between the floor and door. While I had the dishwasher pulled out, I discovered another problem with the pulleys and strings that prevent the heavy door from flopping down, but I won't include this repair. The pump and motor must have been failing for some time because the dishwasher is much quieter now and the dishwasher is much faster. I am sure the plugged screen didn't help either.
This site is wonderful..., thank you. Especially thanks to Nanette's detailed experience. The thing that gave me the most problem (and apparently Nanette, as well) was removing the lower round cover of the chopper assembly. Finally, some one on the internet identified the trick...put needle nose pliers in the screw-hole and pull-away. It came right out. Wish I could acknowledge the source but now can't find it. Actually, the check valve was good, but I replaced it anyway. It was 10 times the trouble to replace than the drain pump. Wish I had started with the drain pump. By removing the drain hose, I stuck my finger in the hole and discovered the problem: the impeller was off of the pump and lying in the bottom of the drain. It was a simple thing to replace the pump. Press down on the locking mechanism and turn it to the left. When it was off, I could see that the check valve was in place and not a problem. (Of course by that time, I had already replaced it.) Good luck.
removed both upper and lower racks. removed lower spray arm(left hand thread) removed "water delivry tube and upper spray arm. removed torx screws on pump cover. removed inner chopper cover. Chopper assy had come apart and was full of food crud. cleaned out and installed new chopper assy. kind of tricky don't force it. reassembled. tested OK.could tell sound of more forceful water pressure
I released the heater element from the clips on the bottom of the waaher tub. I pulled the unit out from the wall and disconnected power. There are two slip on wire terminals on each end of the heater element accessible from the back that need to be removed. One of them was badly rusted from leaking water, which had caused the short, and had to be replaced. These terminals and the crimping tool to install them are available at any home center. I removed and discarded the old plastic nuts since one of them was damaged by arching from the short circuit. Moving around to the front of the dishwasher, I removed the old heater and installed the new one. I had ordered new rubber washers, but the new heater came with them already installed. Since one of the old ones failed and caused the leak, they are a good thing to keep around as spares anyway. I installed the new nuts and tightened them to enough to ensure that the washers made a good seal. I reconnected the wire terminals to the heater, reconnected power and moved the unit back into place. The circuit opening when the heater failed caused a "call for service" error and the controller would not allow the unit to run. You will know you have this by the "CLEAN" LED flashing seven times. Clear the diagnostics by pressing the buttons for "HEATED DRY", "NORMAL", "HEATED DRY", "NORMAL" and after the controller resets, the dishwaher is ready to run. It's worked like new ever since.
This unit was unique that whole motor assembly was held in its place by two plastic clip. The gasket had few rings that worked as place holder, although gaskets don't go bad often this model could be if it gets pulled alot and if motor assembly get pushed it will push up the gasket and cause a leak. Repair was simple, 1) take spray arm off from inside. 2) get under neath the dishwasher, take off wires so it would free up some room, pulled two plastic holder out, gently push the motor assembly up to the tub, 3) from inside the tub, pull up the assembly enough to get your hand under the gasket and pull them off. 4) Replace the gasket, align the assmebly and push down to snap in the gasket. 5) get under and push in two plastic clip back in, put wires back into its place. Back in the tub to push down the assembly again to make sure there are flush with surface. Put spray arm back on. Finished.
First: Turn power to the Dish washer OFF, then remove the two panels at the bottom of the dishwasher. Two: remove the Door face panel for easier access to the inlet-Valve. Three: remove screw that holds Inlet-valve bracket. Four: slide Inlet valve bracket left and back to get out of slots. Five: Holding the Inlet-valve forward loosen and remove water line (copper tube nut / pressure fitting). Six: Remove two wire clips Seven: Remove platics hose (Spring Clamp) Replace Inlet-Valve and reverse process///
Turned off power, turned off water supply and diconnected, slid out dishwasher. Removed the spray wand and tilted dishwasher to access the two nuts and disconnet the wires. Removed the two nuts using a socket. Removed the old heating element and replaced with the new one secured with new nuts ( the old ones were fine but since I bought two new ones why not). Pluged the wires back up slid the dishwasher back in hooked up the water reinstalled the spray wand cut on the water and power. Good as new.
Dishwasher Quit Running On The Pressure Side (Pump Motor Went Bad).
Turned off water and disconnected line, then disconnected drain, turned off power and slid dishwasher out and turned turned upside down and removed hold down bolt ( it is a 3/8 head bolt) removed wire from motor and twisted motor assembly approximately 1/4 turn counter clock wise and removed old motor and seal assembly reinstalled new motor with new seal and rewired. Turned washer back upright and removed filter assembly and lower jet arm, removed cover for food disposal and reinstalled disposal blade back on pump drive reinstalled cover and filter assembly and jet arm. Slid unit back in place and anchored down to cabinet and turned water and power back on ran washer through a short cycle to clean any soap build up that was left inside and that was it, it all works just like new.
Replaced electronic control panel first which had an obvious defect (burned terminal). Still no power. Replaced fuse and works fine now. Took lots of reading to find out the dishwasher had a replacable fuse. Even the appliance store didn't know.
Via your web-site I was able to download the step-by-step screen-shot pictures. I was really surprised on how easy the detailed photo screen shots made the repair really easy! Thanks for making this repair a piece of cake. If I should ever need additional parts for any of my home appliances I will certainly order my parts through PartSelect.
The overhead water spinner became detached and fell off
First I removed the screw from the top water tube and then the upper screw from the vertical water tube at the back of the dishwasher. That gave enough flex to the tube assembly for access to the area I needed to get to, without having to remove it. Then I removed the old spinner retainer and installed the new one. I then snapped the spinner to the new retainer pin, put the tube back into position, and re-installed the screws -- and I was done.
Thanks to the previous review of this part, I was able to figure out how to do the replacement myself and saving $150 on a service call. The part is super easy to replace. Remove the screws on the door, lift the outside piece of the door up and off the hinges and then unplug the old piece. I had turned off the electricity to the dishwasher to avoid getting shocked. There were 4 hex nut screws holding the part in, removed those & popped out the old part. Installed the new one, put the door back on and the screws, turned it on and no leaks. This part was so easy to replace, even for a 52 year old woman like myself!
The ceramic seal had failed, allowing water to destroy the front motor bearing.
Removed dishwasher from under the counter and took it to my shop. With the washer on its side, I removed the motor, then the impeller and seal. I then disassembled the motor and replaced the front bearing(purchased separately). This required an arbor press. I then reassembled the motor and installed the new seal and impeller. Reassembled in reverse order. Reinstalled under the counter and made conections. Checked for leaks and proper operation.
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
19 of 26 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water pump motor was making a grinding noise
I had a repair guide for my dishwasher which helped. First I removed the water distribution system inside the dishwasher and then removed the door panel. Next I removed the front bottom access panel. I placed a pan under the pump and hoses to catch water when I removed the outlet hose. Very important here! One must remove the pressure switch from the outlet port or else you can't get the pump clear of the washer tub. Next I removed the drain pump by releasing the catch and turning the pump counter clockwise. Now for one of the hard steps. I had to remove three pins which hold the pump assy to the wash tub. Two of them are out of sight so you have to weave you hand past all the hardware and "feel" for the back two. At this point the pump assy just lifts out. Remove the motor /pump by removing one bolt and turning it counter clockwise and withdrawing. I put the new one in. Don't forget to put the pump screen in as I missed this and had to redo the job. Reverse all the previous steps being careful to keep the motor guard out of the pump seal area. Use lots of silicon seal grease and check for leaks on first power up. It took me a couple of adjustments to get a leak-free seal.
1, I shut off ac circuit breaker. 2.Shut off water supply valve. 3.disconnected water line from inlet valve. 4. disconnect the drainage hose. 5. have plenty of towels to mop up water. 6. Remove racks and disconnect water diverters inside the tub. 7. remove phillips head screws that hold dish washer to counter. 8, Pull out DW and lay on its side to expose bottom of dishwasher. disconnect the motor terminal plug. and disconnect the temp prope. 9. disconnect the drainage tube and then proceed to remove the 3 plastic clips that hold the pump housing to the tub. 10. I used some silcone grease around the new pump housing to be safe. then I installed the new pump housing and motor in the reverse order.
It probally took me about an hour start to finish, the hardest part was placing new housing back in. The ring around the bottom of tub is very sharp! Left some blood there.