Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The Crisper Glass Shelf Broke
The Crisper Glass Shelf Broke. My son removed it to clean and dropped the shelf. I ordered a replacement shelf which arrived in record time and just slid it into place.
No instructions came with new parts. Access to element was impossible until I accidentally discovered that the two styrofoam cushions at the ends of the coils were removable. Once removed, access to the heater and thermostat was very easy.
Unplug appliance, remove freezer shelf, cold air ducts, back of freezer, disconnect light, (My model does not have ice maker. This may also need to be disconnected.) 1.Remove styrofoam cushions at end of coils 2.Locate element between bottom two coils 3.Disconnect the male/female connections 4.Remove support clip under center of element 5.Remove element 6.Replace new element in reverse
Connecting the thermostat wires was challenging because they were somewhat behind the coils.
1.With styrofoam removed, unclip thermostat from coil 2.Carefully cut wires (leave enough to connect new wires) 3.Connect new thermostat wires (color of wires matched on my fridge) 4.Clip new thermostat in place 5.Replace styrofoam 6.Button it all up
With these steps, this job would take maybe 30 minutes; somewhat longer if your model has an icemaker.
Poped out with screwdriver the old swithch and unplugged the two wires. Plugged in the wires to the new swithch and pushed it back in the hole where the old switch was before.
I took the broken part off the bar, put the new part on the bar, snapped it into the fridge, threw the old part out, opened the fridge admired my work, while I was ther I grabbed a beer....couldnt have gone better.
Pulled refrigerator plug from socket. Removed all freezer items. Put them into sink to keep cool. Phillips head screwdriver removed screws from plastic housing fan cover from rear of freezer compartment. Removed fan housing panel by lifting up and out. Panel has two small tabs that fit into back panel. Removed back panel with phillips head screwdriver. Fan is now exposed. Not working. Plugged power cord back in. Disconnected power adapter to fan. Voltage meter sees power to ground and hot wire. Fan not working Unplugged power cord. Removed fan from rear by socket tool. Used hair dryer to remove ice build up in styrofoam insert between freezer compartment and lower section. Removed foam insert....broke a couple of pieces off. Test new motor with a line cord wire stripped at ends Motor works. (Old one did not work with same test) Replaced fan into bracket. Replaced bracket into rear of freezer. Plugged power cord in. Fan does not work.....Whoa!!!..closed freezer door and heard fan running!!! It works. Replaced everything...foam insert, panels, food. One week later, still working..... (Now...I don't know why the fan did not start right away...it may be that there's a small round thermostat sitting on a copper tubing, that needed some time to kick in...but that's a supposition.) Have fun
The condensor fan in the unit appeared to have been chewed by a mouse and would not function and the lower door was too low.
The condensor fan in the unit appeared to have been chewed by a mouse and would not function. We had a service call to verify this and ordered the parts. Delivery was extremely quick and we were able to complete the repair and place the unit back into service within 2 hours.
All that was necessary was to remove the bottom cardboard cover, replace the fan and grommets, and replace the door bushings.
Switch failed on which kept the refrigerator warm due to heat generatered by light bulbs.
While the switch did last for 9 years, the design is poor due to the failure mode. The failure should be to fail off or not able to turn on the lights which would be inconvenient but would not warm the refrigerator contents. Arcing at the contacts eventually caused the switch to "weld" closed. It is not obvious that this is occurring so it took some time to recognize why the temp inside the ref was high while the freezer was OK. Replacing the switch was easy once it was recognized as the problem. All that was required to replace the switch was to remove the screws holding a fiber cover and then pulling off the aluminum cap which covered the switches. Unplug the switch an squeeze the keeper on the switch to release it and pull down. Pop the replacement switch in place and plug the wires harness back in. All in all it took much less time to replace than it has to write this up. T Pope
I removed the fan housing , this was the hardest part , this took loosining two screws and snapping the housing loose , and there it was , settin there Idle and the coils were all ice , I let the coils thaw while I unscrewed the fan mount from the back wall of the freezer , then pulled the fan and mount out far enough to snap the wire connector loose, then I removed the two screws that hold the motor to the mount , the new fan motor comes without the blade so the blade is removed by pulling fairly had on the center off the shaft , the old motor is taken out of the mount , the new one replaces it perfectly , then the screws are replaced and tightenen , then the blade is pushed back on the shaft , the motor and mount are placed back on the back wall of the freezer department and screwed in place , the wires connected , then the housing is snapped back in place and the screws tightened , turn the dial to cool or number 2 or 3 and " bingo " it,s just like new , I can thank part select for speedy service and delivery
The plastic cover broke - probably too many heavy bottles on it.
Had to take out everything on the shelf & pull out the vegetable draws, then proceeded to clean it all. Had to take out the glass inset in the cover & wash that. After that I just slid it in - piece of cake! The hardest part was to get the plastic cover off the new part!
The existing light switch was very hard to remove. I ended up having to grab it with a pair of pliers and pull it out. Once it was out, it was very easy to put in the replacement and it seems to be working fine.
Not only was finding the part rediculously easy for a person who has never done this type of thing...the repair was a sinch!! I will always return to this company for help with home equipment repairs. I saved so much money doing it this way. :) thanks guys!