Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Door Handle bracket was broken
Unscrewed the broken door handle from the range with torqx bit, and replaced, hardest part was getting the plastic handle on the black pull bar. you may want to use a mallet.
The stove's burner bowls were dirty and old and the chrome was gone where the cooking drippings had collected under the previous owner's usage.
We simply typed in the model of the range and several selections of replacements came up on your website. We ordered the black porcelain ones to replace the old chrome ones, thinking they might hold up better and be easier to clean. They look great and I really think they WILL be easy to wipe up. Thank you, Part Select! Patty in Indiana
For 12 years I've been suffering with the incorrect burner bowls...I love to cook and it's really irritating when your bowls don't fit correctly. Now, I am amazed at how my burners fit! Thank you! What a Blessing!
Using a torx screwdriver, I removed the old handle bracket. I had to be careful not to lose a metal spacer that went between the back of the door front panel and the back of the inside door panel. With the door in full open position, I was able to hold this spacer in my thumb and fore finger while I removed the screw. The broken portion of the handle bracket fell to the floor. With the old handle removed, I placed the screw through a hole in the inside panel, through the spacer and through a hole in the front panel. While holding the front pull bar in the right handle bracket, I placed the new bracket on the bar holding it in position on the door and attaching the screw. Easy peasy!
The door handle end caps did not fit on to the handle far enough. this caused the screw hole spread to be too wide, Also the new end caps had two nipples outside the bolt holes that the original brackets did not have.
The reason the brackets didn't go on to the handle far enough was there was a molding defect inside one of the brackets. After alot of scraping at the inside of the bracket and lightly tapping with a soft hammer I was able to get the defective bracket on so that the holes lined up to the mounting plate. As for the extra nipples I had two options. Either cut the nipples off or drill some holes in the metal plate that the brackets attach to. I chose the latter. I had to attach the brackets to the plate with extra long screws, reach in under the bracket with a scribe and mark the nipple location on the plate. Then I removed the handle and drilled two holes for each bracket. After some minor adjustments to the holes I was able to attach both brackets and reassemble the oven door.
Pull door from oven and place on flat work surface. Remove bottom screws then the top screws and separate the two halves of the door . Remove broken door handles and replace reassemble door and place back on oven. The hardest thing was to clean the grease out of the inside of the door and get the glass clean to reassemble the door.
Door handle end cap got brittle and broke on oven door.
Slide oven door off slides and put oven door on table. Removed 2 torx-20 screws from top of oven door on the inside. Remove 4 sheet medal screws from the bottom of door 1/4' socket heads. The inside of the door will now separate from the front of door.Now you can see 2 screws on each side of the door handle end caps on 1/4 " socket heads. Remove the 2 screws on which ever side is broken and remove old end cap and side new one on an install 2 screw. When you put door back together there are 2 spring steel spacers that fall off the top 2 screws that hold the inside and outside at the proper space! Parts Select service is EXCELLENT!!!!!
one leg of the terminal block was loose and overheated under load.the terminal block melted and could have caused a fire.
I took a picture of the setup and damage . I then disconnected the burnt wires and replaced the wires . Then I installed the new terminal block and connected the wires to the proper positions. The reason for the failure was that the delivery people didn't tighten the cord when they installed the stove . I would check the connections periodically as to avoid another situation like this .
Removed door from oven. Removed all side screws and pulled front assembly from door. Discarded old screws and broken plastic pieces. Put old handle in new end caps and lined them up with screw entry holes. It took 2 people to hold the door up while pressing in the screws to enter the new plastic receivers on the end caps. A pretty easy fix.
The burner bowls were encrusted with grease and spills.
I easily took out the old ones and put in the new ones sent by Part Select. As promised they fit perfectly. Now when my wife cooks there is no more smoke and it does not set off the smoke detector.
