Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
When washer was in cold water rinse cycle, loud squealing noise.
unplug unit first Took water & drain hose loose, used two wheel dolly, took washer out on patio. Removed water hose. Removed two screws # 49 an laid back control unit then Removed 2 #6 Clips Top of unit, then pried back unit cover out enough to remove Water valve after removing #4 screw that holds unit to back panel ,removed hose clamp #21 an electric connections, install new water valve and put back together..DO NOT TAKE BOTTOM SCREWS FROM BACK PANEL, if so the bottom will drop.. Intake cold water valve was half stopped up. Also new water lines.
Move dryer away from wall. Unplug the dryer. Open the hinge top from the front edges of dryer. Remove the two screws holding the filter channel onto the top of dryer. Lean the top of dryer back away from the front . Open the dryer door, Locate switch from the top looking into the dryer top opening where you have just leaning the top back out of your way. Unplug the wire from the old switch. remove the old switch and bracket using the flat blade screwdriver for screw removal. Place the wire on the new switch using the normally open contacts. place switch on bracket and gently position the bracket and switch over the holes designed for the switch and tighten screws using the new Phillips head screws sent with the new switch. place the top back into place and replace the filter channel screws plug in the dryer and job finished. easy as 1-2-3
Turn water off at the inlet valve of hose you are replacing. Disconnect inlet hose the washer and let water drain out in a bucket. Then remove old hose. Replace new hose to inlet valve then washer . Use pliers to tighten both ends. Turn on water to check leaks at both ends of hose.
Order the part and put the new part on and put the washing machine cabinet back on and check the washer for the water filled up and then it's starting to go on the spin cycles.
Raise the top off of the dryer with a flat blade screwdriver in each front corner of the dryer. Disconnect power to the dryer. Remove old switch and install new switch. Test door and proper operation of dryer.
Unplugged the power while the washer was running, and the water kept on running. The water inlet valve was stuck open. I removed the inlet valve and you cold blow air thru it, it should be closed with no power applied.Ordered replacement from this site it was a perfect fit. As far as the removal and installation procedure, just follow the video as presented on this site. Good Look.
1- Unplugged washer. 2- Turned off water supply to hoses hot and cold. (marked hoses H C) 3- Unscrewed hoses to washer. 4-Used phillips head screw driver to take out screws(2) at corners of washer. 5- Slid top of washer forward and lifted top off. 6- Took out retaining clips on each side of washer. 7- Slid frame of washer outward exposing rear panel of washer for access to water inlet valve. 8- Used 1/4" drive to take out screw to inlet valve. 9- Removed inlet valve, unplugged the two connectors and removed clamp from hose to valve. 10- Replaced new inlet valve and reversed the process to assemble washer back together. Total time for repair, about 45 minutes. I now have full running cold water to washer. Thanks guys for the video you provided. Would purchase again if needed. Thanks again!!! Water Inlet Valve with Mounting Bracket Part Number: PS334646
Cold water input into the washing machine was very slow.
The hot water hose was frozen to the hot water bibb and it took me a while to cut it loose with my Dremel tool. Removed the cabinet and replaced the water inlet valve easily, then hooked up new hot and cold water hoses. Reinstalling the cabinet was a little tricky getting it lined up correctly. Checked for leaks then tested the washing machine and it ran great with the water filling the machine much faster with the new Water Inlet Valve. I will definitely replace the washing machine hot and cold water hoses every 5 years from now on.
Removed top control panel, removed inlet mount hardware, removed both electrical connectors, removed filler hose, Installed new inlet valve in reverse order. Works fine !