Frigidaire Range Wire Plugs and Connectors

Videos!

Your Price

$6.40

Terminal Block Kit

★★★★★

34 Reviews

PartSelect Number PS470125

Manufacturer Part Number 5303935058

This part connects the wire harness to the surface element and is used for ranges. The kit includes interchangeable mounting brackets, ceramic wire nuts, heat shrink protective tubing, and wires. If your range/oven is having symptoms such as burner not heating, heating elements not working, burning smell, or if the oven is making a buzzing noise then this could be the solution. The tools needed to replace the kit are wire strippers, a heat gun or hair dryer, and #1 square heard screw driver. Refer to the installation/instructional video for further guidance to accurately replace the element.

Fixes these symptoms

Element will not heat
Oven not heating evenly
Will Not Start
See more...

Installation Instructions

Steven from Taylors, SC

rental property stove only had 2 working burners and bottom drawer off track

first i took out burners then i took out the screws of the termnal block bracket. i then raised the lid on the stoveand clipped the wires on all 4 of the terminal block kits.i then slipped the shrink wrap on wires and used the wire nuts to connect wires together then heated the shrink wrap. I then put screws back in terminal block brackets. I then put the burners on while looking under lid so i would know they were making good connections as this is a bad design from factory. if you pull out burners to clean them and they are not put back in right you dont have a good connection and that causes the terminal blocks to get hot and melt. thats what happened in my case.
As far as the drawer glides they just snap into place Read more...

Videos!

Your Price

$6.65

Main Terminal Block Kit

★★★★★

12 Reviews

PartSelect Number PS471605

Manufacturer Part Number 5304409888

Terminal block kits are also known as terminal boards, or terminal strips, and they are found in a wide variety of household appliances. Most often in ranges, wall ovens, and dryers. This kit attaches the power cord to the inner wiring of your appliance. If the terminal block is faulty, your appliance will not get the power it needs to operate properly. When removing the old block pay close attention to the wire placement, this will make installing your new part much easier. If you notice any of the wires or wire terminals are corroded or damaged they will also need to be replaced.

Fixes these symptoms

Element will not heat
Little to no heat when baking
Little to no heat when broiling
See more...

Installation Instructions

Timothy from Spring Valley, AL

Cord was not tightened enough by delivery crew.

PF alarm appeared on display. Noticed clicking when cord was moved. Had arced for some time and melted original block. New part slightly different. Only has 3 lugs, old one had six. Stack using washers provided. Take note of colors before disassembly. Use caution while working through access opening. The edges are sharp. Only tools needed are phillips screwdriver, deep socket for lug nuts. Nut driver optional. Hope this is helpful. Read more...

Your Price

$49.01

Terminal Block Kit

★★★★★

4 Reviews

PartSelect Number PS2333392

Manufacturer Part Number 5303935271

Fixes these symptoms

Will Not Start
See more...

Your Price

$10.58

PLATE

PartSelect Number PS2332773

Manufacturer Part Number 316542600

Your Price

$72.27

Terminal Block Kit with Ground

PartSelect Number PS900232

Manufacturer Part Number 5303935238

This part is found between the rear wall shield and back panel.

Fixes these symptoms

Will Not Start
See more...

Your Price

$50.47

TERMINAL BLOCK

PartSelect Number PS467705

Manufacturer Part Number 5303323704

Fixes these symptoms

Element will not heat
See more...

Installation Instructions

Jerry from Afton, OK

Old top was rusty and terminal block was cystelized and dangeling

Remove burners, liners and screws in modular plug's (Terminal Block's). Remove two screws under front lip,(open oven door, to gain access)raise top of stove to access screws at the rear hinge's (its easier to remove screws on the pivot and the support). Remove the grounding screw at center rear of top. Lift top off. Replace in reverse order. As a matter of information,the smallest tip will be needed. To replace the terminal block, use a small pair of needel nose pliers to squeeze the electric wire ends from inside the terminal block, plug the wires into new treminal block, no need to worry about which wire goes in which side. Read more...