Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
Electronic Clock and Timer Kit WB19X10006
Fits your JRP14G*J1!
Rated by 4 customers
A Bit Difficult
1- 2 hours
Ratings submitted by customers like you who bought this part.
Fits your JRP14G*J1!
PartSelect Number PS233996
Manufacturer Part Number WB19X10006
Manufactured by
GE
Product Description
Electronic Clock and Timer Kit Specifications
This electronic clock replaces the mechanical clocks with a more reliable digital timer. As per the manufacturer, this part should be installed by appliance repair person.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part fixes the following symptoms:
Timer will not advance
This part works with the following products:
Range, Wall Oven, Microwave Oven Combo.
This part works with the following products:
General Electric, Hotpoint, Kenmore.
Part# WB19X10006 replaces these:
AP2633678, 3595, WB19X0134, WB19X0142, WB19X0143, WB19X142, WB19X5223, WB19X5231, WB19X5269, WB19X5282
Customer Repair Stories
Average Repair Rating: 2.1 / 5.0, 4 reviews.
What's this?
Sort by:
- < Prev
- 1
- Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
After 33 years our double oven clock stopped working.
I studied the drawings on the instruction sheet off and on for about 3 hours. I'm 76 and my memory and ability to identify the relevant parts of the old and replacement clock as depicted on the drawings aren't what they were a few decades ago. I took my time studying this until I was confident that I knew which wires needed to go on which
... Read more
terminals on the new clock module. It took me a while to figure out which side (left or right) of the drawing for the old and new clocks were at the end of the module and which side was adjacent to the rest of the module. Careful study of the drawings and examinations of the modules cleared this up. It also took me some time to figure out if the top or bottom of the drawings as depicted on the paper matched up with the top and bottom of the modules when viewed from the front of the oven. After this became clear removal of the wires from the old module (I labeled all of them with masking tape, for example, as L1, L2, common or neutral, Output 1 and Output 2) and placement on the new module was quite straight forward. I then covered all bare wires with the rubber insulators or electricians tape. However, the clock didn't light up when the panel was reassembled and the power was turned back on. I hired a local appliance technician to examine my work. He found 2 wires touching that weren't supposed to be touching where they plugged into the module. After separating them and turning on the power the clock has worked perfectly. The metal bracket on my oven worked with the new clock module. I didn't have to use any of the new brackets that came with the new clock. A few other manageable problems: I needed a torx screwdriver I didn't have to remove 3 screws holding the panel holding the oven dials and clock module on to the oven. A neighbor provided the needed screwdriver. I cut my index finger when removing the black knob attached to the lever used to lock the oven during cleaning. A band aid stopped the bleeding and allowed work to continue. The spring fitting over the end of the lever that wedges the black handle in place cut my finger. I'll use a pliers or protect my fingers with a towel the next time when removing this knob. I had a few hiccups doing this task but am thoroughly pleased with the end result.
Read less
-
Thomas from KNOXVILLE, TN
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers
11 of 12 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Electronic Timer went out and Top Oven No Longer worked
There are about 12 wires behind the panel...and this was the second time I've replaced the electronic clock in the past four years. I replaced the analog clock four years ago with the digital version because the analog was no longer available, so I knew what I was in for. There are four screw (top of the frame and lower frame) to remove b
... Read more
efore the frame holding the clock will come out. First DISCONNECT the power! You've have to remove the clock control knobs, and the plastic lever on the self cleaning handle. The first time I ordered this replacement part from PartsSelect there was a diagram included on which wire goes where. This time there wasn't! So it gets a little complicated. Make sure you label all the wired before you disconnect the old clock panel. Anyway, remove the four nuts holding the old clock in place; put the new clock panel in; replace the four nuts. I'll be glad to talk anyone through the rest and I have photos of the whole repair.
Read less
-
David from Owings Mills, MD
-
Difficulty Level:Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Pliers, Screw drivers
60 of 73 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old mechanical timer worn out.
This digital timer, GE Part # WB19X10006 (PartSelect PS233996) is called out by GE as the current replacement for the mechanical timer in the JB500G*J1 range. I had tried to get one some time ago from another dealer but was told it was discontinued and no longer available, so I was pretty happy to come across it in the PartSelect catalog.
... Read more
It comes with a number of mounting brackets and instructions to use the brackets that resemble the old parts, but when I did that the control buttons did not line up with the holes in the glass and were offset about 1/4" to the left. It was impossible to simply slide the timer over that far because it bumped into the underlying metal frame. I ended up using a longer set of brackets which lifted the timer about 1/2" off the glass, thereby avoiding interference with the frame, and bent the brackets sideways to line up with the holes in the glass. But then a transformer on the new timer stuck out about 1/4" too far in back to get the rear cover back on. I made two vertical cuts in the rear cover from the edge down past the timer and bent the resulting flap around the transformer. The resulting installation looks like it was made that way and works great.
It comes with a number of mounting brackets and instructions to use the brackets that resemble the old parts, but when I did that the control buttons did not line up with the holes in the glass and were offset about 1/4" to the left. It was impossible to simply slide the timer over that far because it bumped into the underlying metal frame. I ended up using a longer set of brackets which lifted the timer about 1/2" off the glass, thereby avoiding interference with the frame, and bent the brackets sideways to line up with the holes in the glass. But then a transformer on the new timer stuck out about 1/4" too far in back to get the rear cover back on. I made two vertical cuts in the rear cover from the edge down past the timer and bent the resulting flap around the transformer. The resulting installation looks like it was made that way and works great.
Read less
-
Theodore from Atwater, CA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Pliers
26 of 32 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Mechanical/electrical clock/timer not working
Followed the instruction provided except had to add a NEUTRAL LEAD which on the old part had been provided by the frame as it was metal/ electrical vs plastic/electronic . Used one of the extra Wire Extensions provided, drilled a hole in the clip connection and attached it to the metal frame holding in the replacement clock. The need for
... Read more
a NEUTRAL LEAD was not discussed in the instructions.
Read less
-
Maxwell from RINGWOOD, NJ
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers, Screw drivers
29 of 36 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- Next >
Back to Top
Questions and Answers
Be the first to ask our experts a question about this part!
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
Sorry, we couldn't find a match for "".
Here's a guide for finding your model number.
Something went wrong. Please try again later.
Your Question Has Been Submitted!
Our experts will send you an email as soon as your question has been answered.
Back to Top
You May Also Need
?
Back to Top
Model Cross Reference
This part works with the following models:
PartSelect Number: PS233996
Manufacturer Part Number: WB19X10006
Manufacturer Part Number: WB19X10006
Brand
Model Number
Description
Back to Top
Electronic Clock and Timer Kit
$
506.13
Special Order
✖
Stock Status
In Stock
Item is in stock and will ship today if your order is placed before 4:00 PM Eastern Standard Time.
If your order is placed after 4:00 PM EST, the in stock items will ship on the next business day.
On Order
Item is not in stock and usually ships 3-5 business days from the time you place your order.
Special Order
Item is not in stock and usually ships 10-15 business days from the time you place your order.
NLA - No Longer Available
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.