Make sure you haven't got the discount earlier.
Multi Rib Belt 56095
Fits your TGA400 Dryer!
Rated by 4 customers
Really Easy
30 - 60 mins
Ratings submitted by customers like you who bought this part.
Fits your TGA400 Dryer!
PartSelect Number PS1617491
Manufacturer Part Number 56095
Manufactured by
Whirlpool
Product Description
Multi Rib Belt Specifications
At 93-1/8" inches in length, and 3/8 of an inch wide, this flat dryer drum belt has four ridges. It is all black in color and is made entirely of rubber. This belt is used for many gas and electric clothes dryers.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part works with the following products:
Dryer, Washer Dryer Combo.
This part works with the following products:
Speed Queen, Amana, Caloric, Magic Chef.
Part# 56095 replaces these:
AP4061207, 845, 56095, R0606524
Customer Repair Stories
Average Repair Rating: 3.4 / 5.0, 4 reviews.
What's this?
Sort by:
- < Prev
- 1
- Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
load banging noise when drun turns
removed front cover 2 lower screws. once front cover was off, the front drum support bracket was visable. removed 4 screws that hold that in. the drum is now loose and not supported in the front. pulled drive belt tensioner back to release belt. removed 2 top cover screws to get more vertical room to lift drum out. once drum was out, i us
... Read more
ed a snap ring plyers to take retainer ring off to remove damaged rear drum support rollers. replaced both rear rollers. also replaced drive belt and door lamp. the bearing in the left roller had seized and torn a big hole thru the roller . assembled in reverse order. now drum is nice and quiet
Read less
Other Parts Used:
-
Randall from Hoffman Estates, IL
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Screw drivers
9 of 10 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The dryer tumbler belt broke
I opened the dryer by lifting the top and propping it open. I unscrewed two screws on either side with a flat-blade screwdriver, unclipped the dryer stop door micro switch. I slid the new belt over the drum to the center, then used the flashlight to see where it went. There is a tension wheel that had to be pulled to the right and with t
... Read more
he belt in place release against the belt to apply constant pressure during operation. I vacuumed the dryer out and put it back together
Read less
-
John from Dillingham, AK
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Noisy dryer, sounded like drying tennis shoes
Ordered parts per recommendation of expert. Removed front of dryer, removed inner panel, replaced drum support roller, idler pulley shaft, and replaced the belt. Put inner front door on and then front of dryer, voila!!! It works just fine.
Other Parts Used:
-
Cheryl from Flushing, MI
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
8 of 11 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The dryer would sqeak when starting, after running it would quiet down. I thought as long as I had another repair to do, I would replace the belt with a new one.
I removed two nut head screws on the base front panel. Pull the panel downward and the panel came off. Then I removed the two nut head screws off the bottom of the door frame.Pulled out the front frame and pulled slightly downward. I removed the wire connections that were on the door light switch. Then removed the door, and set it aside.
... Read more
With the door removed, I could see the dryer barrel and the belt wrapping around it. I then removed the front frame by taking out the four bolt head screws. I removed the frame panel. Looking in you can see the barrel with the belt around it. I slid the belt off to the rear of the barrel. I then slid the barrel out the front of the case. I then removed the belt. I installed the new belt around the idler arm and the motor shaft. (lay the belt in the rear of the case. Then reinstalled the barrel and set it on the two rollers in the rear. I then reached around the barrel toward the rear of the case and pulled the belt up and over the top of the barrel.Keeping the ribbed side down against the drum.
Put the front frame and four screws back on, keeping the barrel centered and seated in the frame front. Then reattach the door and door frame, making sure to rehook the wires for the door light switch. Then reattach the bottom two screws and the bottom panel. All done.
Put the front frame and four screws back on, keeping the barrel centered and seated in the frame front. Then reattach the door and door frame, making sure to rehook the wires for the door light switch. Then reattach the bottom two screws and the bottom panel. All done.
Read less
-
Gary from Wellsboro, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
13 of 16 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- Next >
Back to Top
Questions and Answers
Be the first to ask our experts a question about this part!
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
Sorry, we couldn't find a match for "".
Here's a guide for finding your model number.
Something went wrong. Please try again later.
Your Question Has Been Submitted!
Our experts will send you an email as soon as your question has been answered.
Back to Top
You May Also Need
?
Back to Top
Model Cross Reference
This part works with the following models:
PartSelect Number: PS1617491
Manufacturer Part Number: 56095
Manufacturer Part Number: 56095
Brand
Model Number
Description
Back to Top
Multi Rib Belt
$
47.49
Special Order
✖
Stock Status
In Stock
Item is in stock and will ship today if your order is placed before 4:00 PM Eastern Standard Time.
If your order is placed after 4:00 PM EST, the in stock items will ship on the next business day.
On Order
Item is not in stock and usually ships 3-5 business days from the time you place your order.
Special Order
Item is not in stock and usually ships 10-15 business days from the time you place your order.
NLA - No Longer Available
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.