Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Stove top element not working due to bad receptacle.
Turned off the power at the breaker box, cut the wires approximately 5 inches from the bad receptacle and removed it after removing one screw. Stripped back the wires about 1/2 inch and attached the new wires with the ceramic wire nuts provided and secured the receptacle back in place with the new screw provided in the kit. My sister's husband wanted to scrap the whole range but I repaired it with $14.00 worth of parts. The element is working great now. Whenever I need appliance parts again I'll use partselect.com.
Oven not holding 350 F, when cooling the coils did not reheat
Removed the oven door by opening slightly, then pic door up to remove. Remove 2 screws holding oven sensor in place, gently pull on sensor to remove, had to remove about 8 inches to get at plastic connector. Unplug connector, had to use an adapter cable supplied with the PartSelect kit to install new sensor, push cable back into opening, reinstall 2 screws. The oven works fine! Note that due to thermal lag the temperature overshoots to 370 degrees and undershoots to 340 degrees, this appears to be normal oven operation. Putting door back in place was easy.
Turned the breaker off, I removed 2 screws securing the range top to the range, opened the top and secured it in the up position, Removed the 2 screws securing the element ,one at a time I swapped the quick connectors from the old element to the new and repeated the process in reverse. I save over $100.00 in labor, plus most companies get you for a trip charge. It was easy!!
Thermal switch is integral to element and can not be changed, must replace entire element.
Turn off power. Removed front two screws above oven door jamb and lifted the top. Removed the bracket that holds the element against the glass top and removed the element. Moved brackets from old element to new one, aligning to same numerical position and then moved wiring to new element. Slide new element under bracket and reinstalled single screw. Replaced top and screwed down. Turn on power and test .
mice had made nests in the insulation wrap in the range
I numbered every part. ex: 1 L., for first part removed left side. I used a magic marker to circle the holes and wrote the number of screws used on the part, set the srews in a separete place, so that I new where these screws went to. The cleanup was pretty time consuming, but I was able to keep my stove, when every repairman I called to fix my stove told me I was better off buying a new stove. ($600.00 stove 2 years old)Please Note: The insulation blanket needed for the entire stove is two pieces, the sides and top are one part # and the bottom and back, are another part #. I did not know this. I just purchased the top and sides. I got lucky, the back and bottom were still in good shape. So I guess I should have read the description of the part more carefully to see what it covers, before I ordered it. It took two people two hours to do the work, it was really nice to have an extra set of eyes, to remember what direction pieces of metal from the stove went. I would do it all over in a heart beat instead of buying a new stove.
First turn off circuit breaker to stove. Slide the stove out about 4 inches from the counter to expose the two phillips head screws, one on the left side and one on the right side of touch panel. Take out screws. Then take out four Phillip head screws on the bottom side of panel, this will set panel loose from stove. Carefully pull up touch pad (switch membrane) from control panel; it is sticky glued in place. Disconnect ribbon cables on switch membrane from control panel by depressing cable locks while pulling firmly. Remove switch membrane. Clean area before installing new membrane. Reassemble turn on power and you are done.
First I removed the two screws that hold the element in place. I then pulled the sensor out about 3 inches and disconnected the two wires. Next, I connected new sensor and screwed the new sensor back in place. One area for caution. Make sure that the electrical connection is pushed in past the insulation on the back side of the oven. Failure to do so will cause the plastic plug connector to melt from oven heat.
First removed the old gasket using a needle-nose pliers. Then placed new gasket by inserting the little clips on the gasket. Took 5 minutes. Great instructions from Repair Forum.
This is fairly easy for anyone to do. First I opened up the front (silver part) of the oven door by removing the screws at the top and the bottom. Then I kept on removing the various layers of glass... the 2 outside ones are removed by removing their respective screws and then you get to the inner-most. These 2 inner ones are in a frame that holds them together. I removed the large silver frame that holds the insulation and the 2-glass-frame in it. Just remove the screws and then tilt the insulation frame out a bit to remove the glass frame. You can tilt the entire insulation holder out but the insulation is soft and it starts to fall off. Just tilting it enough worked for me. Then I opened up the glass frame from one end, removed the left-over broken piece of the old glass pane and installed the new one in. Then reassemble. The entire process is very easy - but you will need another person for a few minutes when you remove /reinstall the glass frame inside the insulation holder. You would just need a little help holding everything... nothing technical. I would rate the repair technicality at 4 or 5/10. It could even be a 3 if there were less steps involved. Good luck! By the way, Amana/Maytag wanted $70 or so for the glass and then the repair fee. I got the part here for about $50.
double coil which center coil had burned out on glass top range
Unplug range and remove back panel (4 screws) unplug top burner plugs (2). Open oven door and remove 2 screws from under front of top. Pull top out and up to unhook from back. Remove top and lay cardboard on top of range. Flip over the ranges glass top unit and lay on cardboard. Remove screws from steel bottom and remove from top. Flip over steel bottom with burners attached. Remove attaching clips for burner and unscrew them from the burner then reinstall in new burner in the same place as old burner. Lay new burner on top of old burner and remove one wire at a time, transfering it to the matching plug on the new burner. When wiring is done remove old burner and attach 2 clips to steel backing plate. Vacuum off the glass top and reinstall the steel bottom to the glass top. Flip over the top, remove cardboard and slide top into back of range top and lower into place. Attach 2 screws under front. Reattach the tops plugs at the rear and reattach the back panel. Plug in range and slide back into place. Test units and all other burners. Done...
First I removed the two philips screws inside the oven that hold the element in place. Then I pulled the sensor out and the two insulated wires through the hole to reveal the plastic connector. I unsnapped it from the connector and replaced it with the new element. Then, behind the oven, I removed five or six philips screws on the right side of the large panel so I could pull the wires back through the layer of fiberglass insulation to make sure only the sensor itself would be exposed to the oven's heat. I then secured the back panel again and replaced the two philips screws holding the sensor in place.
3 months after my 5 year warranty ran out, one of the elements on my wife's maytag cooktop "popped". I was curious to see if I could fix it myself and ran across partselect.com via google. Their step by step instructions for determining the source of the problem (i.e. either the element or the control was bad) led me to realize that the element was bad. I ordered a new one -- which arrived in 3 days! It was very easy to replace the element, since I had already taken the glass cooktop off of the range during the testing phase. Thanks partselect.com!
First I opened the door to the oven. Then I opened the box that the part came in. (knife) I then slid the oven rack out of the box and unwrapped the plastic, being careful not to bend or scratch the new rack. Now, this is the tricky part... I had to move the existing rack down one space to make room for the new one. Then carefully slid the new rack in, tipping it slightly and sliding it in. LOL