Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
soap dispenser broke
just put new part in very simple only problem was shipping yall used fedex went to 4 states and one state twice they finally gave it to USPS so it took almost 9 days to get here
1. Unplugged electric chord from wall. 2. Pulled washer out into open area to get behind it. 3. Turned off hot and cold water faucets 4. Used channel locks to remove hot water and cold water hoses from back of washer. Dropping hose into a bucket to catch water from hose. 5. Removed screws (Phillips screw driver) holding top to back of washer. 6. Pulled back on the top and lifted off washer. 7. Arranged new intake valve to mock location and setting of old intake valve. 8. Using Phillip screw driver, unscrewed old intake valve from back of washer. 9. Unconnected wiring from old intake valve. These were easily identified and not needed to mark left right center. 10. Using pliers, pinched hose clips and moved to middle of the hose. Did this for all 3 hoses. 11. Removed hose from old intake and connected to same location on new intake. Repeated for all 3 hoses. 12. Using pliers, pinched the clips and moved to the end of the new intake valve. Did the for all 3 hoses. 13. Using Phillips screw driver, screwed in the new intake valve where the old intake valve was located. 15. Inserted the wiring connects into new intake valve. 16. Reconnected water hoses back into washer machine (after inspecting and cleaning plastic strainer traps) 17. Turned on water faucets 18. Plugged in washer. 19. Ran an empty load for a cycle. 20. Did not fail. 21. Reattached top to washer. Laying down an inch from front and push forward to hear a click or lock. Then screwed in the 2 screws. 22. Pushed washer back into original location.
Watched video on U-Tube , unplug power cord, turn off water, take top off washing machine, remove water hoses, unscrew parts, remove hoses with pliers, install replacement parts, put all back together. Does not leak any more !
Took off top of washer to get access to connector nozzle, which is on top front of washer rubber boot. removed old nozzle, installed new one. Easy peasy
Door would not close because the part that was in the door that held it closed kept falling out.
Order the part through PartsSelect. It arrived in a few days and I (an 81 year old woman) replaced it within minutes with no help needed. It was super easy.
Ordered and replaced the hot and cold inlet valves - followed the instructions off of the video posted on the Part Select website ... completed the repair in less than 10 minutes
Old cold water inlet was leaking , as it progressively got worse,it poured.
With my wife's help( 2 shoukder surgeries ), pulled it forward, unplugged power source, turned Both water supplies off. Removed two phillip screws from each upper ( plastic) holder. Bumped top from front( works really well if you can use both arms,and with rubber gloves on for traction, or go to harbor freight purchase a glass suction cup) . I marked ( with a sharpie) the solenoids/hoses,and wires, ( facing front ,right to left,1,2,3.), removed plugs,loosened clamps and pushed them back,gave each hose a twist,and removed them. Took two screws 5/16 from the back that hold the valve assembly in out. Removed old valve assembly, put new in place, reverse procedure for assembly. Once all is hooked up,and water dried, I plugged in,turned water on watched for two cycles( you need not stand over it,if it leaks you will know it) to double check, installed top,and we pushed it back in place. Very simple to do,these washing machines are so easy to work on. Now we enjoy a dry laundry room,and you can to. ??
YouTube is your friend for many such repairs. See this link for an overall description:
https://www.youtube.com/watch?v=WuvLuC8x4_s
I had to remove the top panel to determine exactly which valve was leaking. It turned out both hot and cold-water valves were defective.
After unit is unplugged and top is removed, it's a simple matter to remove/replace hose connections and electrical connections. It took me less than an hour to complete the task once parts were in hand.
It went great. First of all, thank you Part Select for the video on how to do this myself. My home warranty company was giving me a hard time. Blah, blah, blah. A mechanic friend of mine referred me to this site. Within minutes I found the part I need and a GREAT!!!! price. Ordered it, got it super fast, fixed it my self and my second hand washer is no longer peeing all over the floor. Very very happy. I will definitely be a repeat customer, hopefully not anytime soon. Thank you again for an amazing experience.
Displayed LE error even with a couple of pair of socks as a load
I ordered the Rotor Assembly and Sensor Assy.. Rotor Assy. was not the problem. 1 - 17mm bolt in the center of the rotor assy. 6 10mm bolts to take off the Stator assy. once you have the Stator assy off, upplug the sensor assy and release the clips on the sensor assy. and remove. Install the new sensor assy. and plug the electrical connection back in. replace the 6 bolts and screw the bolts evenly around the Stator. replace the Rotor Assy. and secure the 17mm bolt. Replace the back cover (4 - philips screws. Do a test load.