Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Moisture sensors need replacement
Inside the dryer tub, remove the filter housing by removing two phillips head screws. Unplug the sensor wires, note when replacing wires, black wire goes on upper sensor. Separate filter grill from housing. Using the pliers, compress the tabs on the sensor plugs and push it thru the grill. The small blade screwdriver may come in handy here to pry up on sensor to assist in pulling the plug end through the grill. Replace the sensors by hooking short end into grill and pushing the long end through the grill. When replacing the housing to the dryer, the most difficult thing is getting the screwdriver onto the recessed screws. Be sure to put the tab on top of the housing under the dryer frame when rotating the assembly into place.
Removed the two screws under the lint trap Opened the top (had to use flathead screwdriver to release latches) Disconnected door switch harness from front panel Removed 2 screws holding front panel on dryer Lifted out dryer drum (previous belt had broken) Vacuumed inside of dryer (found $3 in quarters!) Put new belt around drum Put drum back in dryer, using empty laundry soap bottle to support its weight Looped belt around pulley and motor; secured pulley to dryer bottom Made sure rear gasket thingy was aligned properly and drum turned freely Put front panel back on Re-attached door switch Closed top and put screws back in under lint trap Fired it up - WOOHOO!
I raised the top of the dryer, removed the front, the belt and the drum. Slipped off old rollers, installed new ones and new tensioner. Reinstalled drum and belt, bolted front back on and closed the top.
When using the dryer the cycle would stop and display E1 as the reason
Unscrewed the bottom panelof the dryer and located the thermistor through the schematic for my machine. Removed the old one and put the new one in the same way. No more E1 problems and all cycles now complete themselves.
Half of my pulley was broken off so there were no wrench flats to take it off. I was able to remove it using Channel Locks and the 7/16 wrench shown in the video.
Hint: Use a one gallon ice cream bucket to hold up the drum while connecting the belt. It makes it much easier and gives you more clearance.
I'm still waiting on my idler pulley. It arrived at Fed EX depot in Tracy CA on December 14th and has still not been shipped. So it is pretty fucking hard for me to install it! Maybe if you had customer service that would answer their phones or reply to my Emails would be helpful
Dryer made a terrible screeching noise when tumbling.
I followed the repair Vedic and took the drum out and replaced the pulls and bracket. Very straightforward job. Dryer is now as quite as the first day we bought it.
Using the Torx Screwdriver, we removed the door from the unit. Then we removed all of the screws on the inside of the washer door. After that we flipped it over and opened it up exposing the inside. We couldn't separate them entirely because there was a screw under the latch piece that we couldn't figure out how to get to. However with all the screws out on the inside of the door, we did have enough room to open it up and access the place cover that holds the hinges in. Once we accessed that we removed the roller tips from the old unit and placed them on the new one. Then we reversed the process. With a couple screws in we realized we had put the hinge in reversed from what it needed to be, so we reopened it and switched it around. Then completed replacing all the screws and reattached it to the washer. It opens and closes perfectly and we saved a couple hundred dollars for sure, as the quote to come out had been a $150 trip charge.
I looked at the parts breakdown to see how it cam apart.
I tore the dryer down, 1. removed the door 2. openned the top 3. removed front panel 4. removed fron bulkhead 5. removed belt and drum 6. removed back cover 7. removed the ductwork 8. removed the fan (this is the hardest part, it is very tight on the motor with left hand threads, there are flats on the (inside of the dryer)fan where the motor shaft goes into the fan for a wrench and you can put a socket on the front pulley on the motor. I ended up just knocking the center out of the fan and replacing it. 9. removed the motor and cleaned the entire unit 10. reinstalled everything in reverse order. Note:I went ahead and replaced the idler pulley and the rear wheels that support the drum, and put a new belt in (just about everything that could fail) I spent about $200 to keep a $1200 dryer in service at least another 7 years.
Open breaker and ensure power was off. Checked heating components for continuity.Found thermal fuse had an open circuit.Replaced High limit thermostat and thermal fuse.Now is a good time time check for free flowing vent piping.I discovered mine was crimped below the floor and caused lint build up and obstructing the flow which could have led to the thermal fuse blowing.I replaced the vent piping as well.My wife says the dryer works better now than it ever has.
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you