It's self-explanatory. The procedure is obvious; it's just a little difficult. The only hard part is attaching the mounting brackets to the fan. If you can't tighten the mounting bolts, loosen them and reposition the brackets. You might end up mispositioning them at first, because they are hard to reach.
I recently bought an old Amana refrigerator for my garage on CraigsList for 75 bucks. It was in great condition for its age, but was missing the post that supports the fruit and veggie crisper drawers. I did a Google search, quickly found PartSelect, and just as quickly located and ordered the missing part, which was reasonably priced. PartSelect promised it woud be delivered in 3-5 days by FedEx Ground and it was. I took it out of the box, removed the crisper backets - and glass cover for them - installed the post and WHA-LA, the crisper backets work just as good as when the fridge was new! Couldn't have had an on-line mal-order operation go any slicker!
use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks
changed the light bulb still would not work so I figured it was the switch sure enough.
I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.
First I completely emptied out all the inside of the refrigerator door to lighten the weight of the door. Then I removed the 3 screws on top of the fridge which held the door in place. It was pretty easy to lift up the door and remove it from the bottom hinge. I removed and replaced the door closure and re-assembled the door.
Unfortunately that didn't fix the issue. The door still doesn't close on it's own. The door doesn't get lifted up at all when I open it so I assume that the counterpart to the door closure within the door itself is broken.
Recently professionaly replaced gasket was not sealing.
Identified the necessary replacement part on partselect.com, ordered the part and paid less for it than we had paid the national repair company for their replacement part. The part was delivered three days later. It was the correct part -- the national repair company took two tries to do that. It was in perfect shape -- unlike the two parts that we had received from the national repair company. With instructions from the internet, the entire process of installing the gasket took me less than an hour. Now we have a good old refrigerator that is like new. Thanks PartSelect.com!
First I removed all the screws from the back cover. 2nd removed fan nut and fan blade 3rd removed fan bracket 4th I traced wire to the condenser and disconnected wires from wire nuts. Installed existing fan brackets to new motor kit then reconnected wire nuts to new motor cord Reinstalled fan nut and blade, reinstalled cover, plugged it in and BAM .WORKS PERF!
Outer case of freezer was heating up, not making ice (sometimes) turned up thermostat several times (especially freezer)
I got the product very quickly. (thank you) Looked at online instructions that were quite vague. Pulled plug.Removed the holder for the fan motor slid it out to see what I had. Removed the mounting screws (3) and slid the motor an fan blade out. I made a cut between the wires and marked the "top" wire to motor to be sure to spin in right direction. Removing fan blade hold down clamp was NOT explained at all but I noted that the shaft on the motor was threaded, so I used pliars and held the shaft white un-screwing clamp. I cleaned the fan blades with degreaser and scraped edges of opening on holder opening. Make sure to use ALL the NEW parts included with this kit when re-installing. They send them for a reason. When slpicing and connecting wires it is a 50/50 shot if you don't mark before cutting. You can connect and try plugging fridge back for moment and make sure it is blowing OUT. Put everything back together and after turning DOWN the thermostats twice, fridge is back to usual. Ice maker is cranking out ice and outside case is cool to the touch.
Note: This can be a DIRTY job especially with 4 dogs in house. Fir and grease don't mix well