Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Ice maker motor would run continuously but the blades would not turn and no ice came out.
I wasn't sure what the problem was, but the ice maker seemed simple and on-line resources suggested the control and motor assemblty was at fault. I searched the internet and Partsource had great diagrams which I could match to the part in hand. The price was right (way less than the local stores) so I ordered it. I unplugged the unit from the power in the freezer, but unplugging the entire refrigerator works too. I pried off the white cover on the front of the ice maker, which snaps in place top and bottom. There are three screws holding the contoller (the entire front piece), remove them, pull off the controller and push the new one in place. You may have to turn the blade shaft to line up the notch on the shaft to the motor. Then reinstall the three screws, The screws go into plastic so it is easy to cross thread them, so be careful, I actually think I did with no ill effects. Snap on the cover and repower the unit. Done. Simple and quick.
Icecubes came out half-way, and refrooze. I figured out, that the melter does not work (HEATER in the icemaker) Voltage measured 105V no load. Studied the Internet, and folloved an advice: shorted the back wire and the blackwire with white stripes.these go to relay contacts. It seems, that the relay contacts are no good on Infrared receiver boaed. I turn off manually the icemaker, when needed
Overall, replacing the ice maker wasn't too bad but it wasn't nearly as easy for me as it seems to have been for some. In my case, the fridge was an Amana and the ice maker was mounted in such a way that disconnecting the power connector was difficult. The ice maker had to be completely dismounted before any access to the power connector was even possible. The short power cables made it very difficult to get the ice maker into a position where I had a good view of the power connector enabling me to see how to release it. The only other challenge was the cup that the water line goes into. The replacement ice maker did not come with the right cup - the instructions said to replace the provided one with the old one. No instructions for this procedure were provided and it looked to me like it might involve significant disassembly, something I wanted to avoid for fear of breaking a plastic part on the new ice maker (something I had already done when disassembling the old ice maker). So instead of replacing the cup, I modified the new one to match the old one. This involved removing a cutout on one side and covering a hole on the other. Installation of the new ice maker went fine and the water leak problem was fixed.
R & R Icemaker Assembly. Took out 3 screws and unpluged Icemaker & replaced with new part. very easy and the service from PartSelect was fantastic. Very Satisfied, Ron Martin
Removed Ice bucket. Removed two screws and removed front cover from old ice bucket, two more screws under cover to remove ice agitator. Installed ice agitator to new ice bucket, installed two screws holding it. Installed ice bucket front cover on new ice bucket with two screws. Put new ice bucket into freezer. Finished! That was easy!
I removed the front cover--just popped off with no trouble. Removed 2 screws at the bottom. Slid the broken part out and put the new one in place. Put in the two screws, replaced the fron cover AND Done!!! BTW I am a 65 year old woman and the icemaker is like new.
I just unscrewed the plate that locks in the light switch (screwdriver) and unplugged the old faulty part and plugged in the new switch, screwed the cover back on and I was done!
While ordering the assembly, I had thought that the ice bucket was included but it wasn't. So I ordered the ice bucket afterwards. Maybe a little more clarity as far as what parts come in the whole assembly would save some time. All in all, the agitator was very easy to install, along with the ice bucket. After securing the agitator to the existing assembly with two screws, the ice bucket slipped right into place. Easy to install.
As the prior stories mentioned, this was a fairly easy fix to a nagging problem. Heck, we almost bought a new refer over this, cuz the door would keep popping open.
Needed a screwdriver, and a 5/16" nut driver (mounted in elec. drill). Have two people for this one! Emptying the door would help out tons too. ('course, I didn't do that!)
With the door closed, remove the plastic cover on top by removing 1 phyllips screw. Then, using drill mounted 5/16" nut driver, remove 3 hinge screws. Remove hing by lifting up. Now, carefully open and remove the door. Here is where the 2nd person comes in. There are 2-3 1/4" screws (Must use a 1/4' NUT DRIVER, SOCKET OR MAGNETIC BIT HOLDER) on the bottom of the door to remove the broken plastic cam. Also, you must remove the bad cam from the bottom hinge using I believe the 1/4" nut driver.
Finally , one person lift the door while the other kneels on the floor to help giude the door back onto the bottom hing pin. Close the door, ensuring that the top of the doors are even, and secure the 3 top hinge screws. UR done!
My icemaker started leaking water into the catch basin and turning my ice into one big ice burg.
Well folks I put up with an ice burg all summer when I really should have took the time to fix it. You know how it goes though. You get so busy you just put it off. Well don't put this one off because this is just how easy it went. I came home one evening and wanted to make a drink to relax but that big glob of ice was there waiting for me. I took a crewdriver and beat it down so I could pull the catch basin out. Having looked it over for a minute I grabed a nut driver and took three of the screws out that held it in. I unpluged the wire and bingo it was out. Maybe five min. had elasped. After taking the unit out I notice how the non stick surface was coming off of the tray and that explains the black pieces that were getting into my ice. Getting the model number off the back of the fridge and writing it down I went to my trusty lap top and did a quick search for a ice maker for my Jenn Air refrigeraton and blamo...! Part Select came up and I put the part number in their search engine and bingo again there it was, my part. One quick order and in three days it was right there by my door when I got home. Now i'm so excited. I went into the house and didn't even chage out of my dress clothes. Within five minutes it was in. Now I just had to wait for the timer to do it's thing and sure enough, I awoke the next morning to a whole tray of beautiful ice cubes. Wow no more ice burgs. The moral of my story is I spent so much time hacking out that glob of ice and for fifteen minutes of my time, I could have been siping on cold ones by the pool but now old man winter is pressing down on me and I guess a lesson learned was a lesson earned. Fix it!
Removed the two screws that hold flaping door. Removed the single screw that covers the connecting wires. Disconnected the wiring plug. I wiggled out the ice maker. Took off the motor cover. Swapped out one motor for the other. Reinstalled the icemaker in the resverse order of removal. Note the wiring plug in the freeze is very from. It makine s the reconnection differcult.
1 screw remove assembly. Unplug cable harness and remove old cover and wire arm. Replace cover and wire arm and attach wire harness on assembly end. Re attach using screw removed in first step. Plug in wire harness. Making ice within 30 minutes.
